Endace DAG 5.2X Скачать руководство пользователя

Страница: 28 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

PCI

Describes the following information about the DAG card:

•

The type of PCI used by the DAG card (PCI, PCIx or PCIe)

•

Bus speed

•

Bus width

Example

pcix 133MHz 64-bit

pci 33MHz 32-bit

pcie 8 Gbs 4Lane

pmin/nopmin (pmincheck)

Enables (pmin) or disables (nopmin) the discard of packets smaller than the pre-defined

minimum size.

Example

dagconfig pmin

dagconfig nopmin

reset

Resets the ethernet framers, set auto mode.

Example

dagconfig -d0 reset

rx and tx Streams

Indicates the number of

and

streams are available on the DAG card. Not configurable.

Stream information relates to the setting of

mem

(page ).

rxonly

Configures the memory hole to only receive.

Example

dagconfig rxonly

rxpkts/norxpkts

Sets whether this DAG card receives packets.

Example

dagconfig rxpkts

dagconfig norxpkts

rxtx

Enables both transmit and receive, and splits the memory hole for

and tx.

This allocates 16MB of memory to each transmit stream, and divides the remaining memory

between the receive streams.

Example

dagconfig rxtx

Note:

This option is only applicable on firmware images containing TX.

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды