Endace DAG 5.2X Скачать руководство пользователя

Страница: 30 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

relative

Sets TR-TERF to Relative Timed Release mode.
In Relative Timed Release Mode, each packet is transmitted according to its timestamp,

relative to the first packet in the transmit stream. This is shown in the following example

where Packet A will be transmitted immediately, Packet B will be transmitted one second

later and Packet C will be transmitted one second after that:

Packet A: Timestamp = 2006-07-24 03:45:55.9720326 UTC
Packet B: Timestamp = 2006-07-24 03:45:56.9720326 UTC
Packet C: Timestamp = 2006-07-24 03:45:57.9720326 UTC

If for any reason the transmission of Packet B is delayed, the module will still attempt to

transmit Packet C two seconds after Packet A. It will do this even if it means reducing the

gap between Packet B and Packet C.
When using multiple output ports in this mode the timing for each port is independent. This

is shown in the following example where Packet A and Packet B are transmitted at the same

time even though their timestamps are one second apart.

Note:

The relative placement of the

packets is accurate to ± 100ns.

Packet A (Port A): Timestamp = 2006-07-24 03:45:55.9720326 UTC
Packet B (Port B): Timestamp = 2006-07-24 03:45:56.9720326 UTC

Example

dagconfig relative

no delay

Disables Relative Timed Release mode (No Delay Mode).
In No Delay Mode all packets are transmitted at the maximum rate permitted by the line

interface, using only minimum gaps between packets.

Example

dagconfig nodelay

tx_crc

Enables the crc(fcs) in the transmitted packets CRC(FCS). Ethernet only.

Example

dagconfig tx_crc
dagconfig notx_crc

txonly

Configures the memory hole to only transmit.

Note:

Only displayed if the DAG card supports transmit (i.e. has a terf image).

Example

dagconfig txonly

Note:

This option is only applicable on firmware images containing TX.

Txpkts / Notxpkts

Sets whether this DAG card transmits

packets.

Example

dagconfig txpkts

dagconfig notxpkts

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды