E9 IN REV. A
9
When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground,
the remote start is disabled.
1. The optional “remote start toggle switch” can be added on to temporarily disable the Remote Start Device, it can
prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced
or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch
to the OFF position. To enable the remote start, move the optional remote start enable toggle switch to the ON
position.
2. If needed, this wire can connect to the PARK/NEUTRAL switch in the vehicle.
(See the TESTING YOUR INSTALLATION GUIDE)
IMPORTANT NOTE: This wire must have a “GROUND” to operate remote start.
Orange/White wire
– 200mA Grounded Output when Disarmed - N.O. Disable
This wire will become grounded when the alarm is disarmed. The current capacity of this wire is 200mA. It can be
connected to optional Ignition disable relay / ECU disable relay / Fuel Pump disable relay.
Black/Green wire – (-) 200mA Timer Control Channel 4
Channel 4 Output (Factory default setting on momentary grounded)
This wire is built-in user-programmable timer output provides a ground through this wire. Press the transmitter
and
buttons at the same time. You may program the built-in timer to send a ground signal for any time interval
between 1 second and 2 minutes. For instance, this timer output may be used to turn on the headlight with the
remote control. Also on certain BMW, Mercedes Benz, Jaguar and Volkswagen cars, you can use this unique
timed output to allow remote closure of all power window and sunroof without the need for an external module!
Black / Violet Wire– (-) 200mA Timer Control Channel 6
(See Alarm Feature Programming)
This wire is built-in user-programmable timer output provides a ground through this wire. Press the transmitter
and buttons at the same time. You may program the built-in timer to send a ground signal for any time
interval between 1 second and 2 minutes. For instance, this timer output may be used to turn on the headlight
with the remote control. Also on certain BMW, Mercedes Benz, Jaguar and Volkswagen cars, you can use this
unique timed output to allow remote closure of all power window and sunroof without the need for an external
module!
Blue wire – Ground Instant Trigger Input (Zone 2) –
This wire is the ground trigger input wire for hood and or trunk pin switches.
Pink wire
– (-) 200mA Programmable Output 2 Steps Unlock Output
(Factory default setting) (See Alarm Feature
Programming)
The 2 steps unlock feature will work for the most fully electronic door lock circuit. The vehicle must have an
electronic door lock switch (not the lock knob or key switch), which locks and unlocks all of vehicle's doors. When
wired for this feature, press the disarm (or unlock) button one time will disarm the alarm and unlock the driver's
door only. If, press disarm (or unlock) button two times within 3 seconds, the alarm will disarm and all doors will
unlock.
Factory Security Disarm Signal Output –
This wire is designed to disarm a factory installed security system. This wire sends a negative (-) 1 seconds
pulse upon a remote start and remote door unlocking. Some factory systems must be disarmed to allow remote
starting. In most cases, this wire may be connected directly to the factory alarm disarm wire. The correct wire will
show negative ground when the key is used to unlock the doors or trunk. This wire is usually found in the kick
panel area in the wiring harness coming into the car body from the door.
Start Status (Shock Sensor By-Pass Control) Output–
This wire is designed to by-pass shock sensor module. This wire will supply an output at all times the remote
start is operating plus an additional 3 seconds after the remote start unit turn off.
Key Sensor By-Pass Output –
This output is for a Key Sense wire by-pass that some Chrysler and Toyota vehicles need to activate remote
start. This wire comes on when remote start is activated and stays on for 20 seconds.
White / Black wire – Negative Safety Shut Down Input
& Hood Trigger