manualshive.com logo in svg
background image

E9 IN REV. A   

15

4

 

 

All Confirmation 

chirps on 

Siren 
Confirmation 
chirp on only 

Horn 
Confirmation 
chirp on only 

All Confirmation 
chirps off 

5

   

+

 

 

Panic with 

Ignition off 

Panic with 
Ignition on & off 

Panic with 

Ignition on & off.   

Panic with No 

time limit. 

Without Panic 

function. 

6   + 

 

With Alarm 

Function 

Without Alarm 
Function 

 

 

7

   

   

Without Car-jack 

mode 

Active Car-jack 

mode  

Passive Car-jack 

mode 

 

8

 

 

+

   

With Dome light 

turns on & off 

after ignition on 

& off (45 second 

door by-pass) 

With Dome light 
turns on after 
ignition off (45 
second door 
by-pass) 

Without this 

feature 

 

 + 

 

Lock/Arm & 

Unlock/Disarm 

Confirmation 

Chirp 

Lock/Arm 
Confirmation 
Only 

 

 

 

 
Exit: 

Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. 

 
45 seconds Delay Door Ajar Error Chirp: 

This feature controls the error chirp that is generated if the system is armed with the door trigger active. This is useful 
in a vehicle that has a long dome light delay after the door has been closed. If the system is armed before the dome 
light has turned off, the security system will generate the door trigger error chirp. Use this feature to disable the door 
open error chirp. 

 
With Dome light turns on after ignition off:

 

Some vehicles turn on the dome light when ignition key is turned off. After remote start, with alarm on, a false alarm 
may occur when the run time elapses and the dome light comes on. To prevent this from happing, program Alarm 
Feature

 A-8

 to “With Dome light turns on after ignition off (45 second door by-pass)”.

   

 

ALARM  FEATURE “B” PROGRAMMING:  

1  Turn the Ignition switch 

‘ON/OFF’ 3 TIMES

 and stay in 

OFF position

.  

2  Push the Valet switch 

4 times

 (holding in on the 

4

th

 push

) until one long chirp is heard then release the valet 

switch. You are now in the Alarm feature 

“B”

 programming mode. 

Press and release the transmitter button corresponding to the feature you want to program.

   

 

Press 
Transmitter 
Button 

One Chirp / LED 
one pulse 

Factory Default 
Setting

 

Two Chirps / 

LED two pulses

 

Three Chirps / 

LED three pulses 

Four Chirps / 

LED four pulses 

 

Pathway 

Illumination  

Feature “off” 

Parking light 

turns “on” for 

30- second 

upon an unlock 

signal 

Parking light 

turns “on” for 30- 

second upon an 

unlock signal & 

10-second upon 

a lock signal. 

 

 

Ignition 

controlled door 

locks & unlocks 

Ignition 

controlled door 

locks only 

Ignition controlled 

door unlocks only 

Without ignition 

controlled door 

locks & unlocks 

 

0.8 second door 

lock & unlock 

3.5 second door 
lock & Unlock 

0.8 second Lock, 
0.35 second 
Unlock 

0.8 sec. dbl 
Lock,  
0.8 sec. dbl 
Unlock 

Содержание E9




























Отзывы: