Emerson SI-EtherCAT Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 106

background image

40

SI-EtherCAT User Guide

Issue Number: 2

Table 6-26 Sync manager 5 PDO assignment object

Sync managers 2 and 3 are used for high-priority deterministic process cyclic data.

Sync managers 4 and 5 are used for low-priority non-deterministic process cyclic data, they
support:

•

A maximum of 32 x 32-bit parameters allowed in each PDO when PDO6 is used (maximum of
12 x 32-bit parameters only in other PDOs).

•

Slot parameter mapping (e.g. SI-Applications Plus menu 7x parameters)

•

Note: when using slot parameter mapping, the data size must be 4 bytes (32 bits)

•

Minimum cycle time of 2 ms.

6.3.5

Feedback encoder source

Table 6-27 Feedback encoder source

0x1C15

Sync manager 5 PDO assignment

Sub-index 0
Access: RW

Range: 0 to 255

Size: 1 byte

Unit: N/A

Default: 1

Type:

USINT

Description:

The number of TxPDOs assigned to this sync manager (used for low priority
process cyclic data).

Sub-index 1 to (sub-index 0)
Access: RW

Range: 0x1A00 to 0x1BFF Size: 2 bytes

Unit: N/A

Default: 0

Type:

UINT

Description:

The object index of a TxPDO to assign to this sync manager.

0x3000

Position Feedback Encoder Configuration

Sub-index 0
Access: RW

Range: 0 to 11

Size: 1 byte

Unit: N/A

Default: 0

Type:

USINT

Description:

This specifies the source for position controller feedback, and the source for CiA402 position
feedback objects, even when position control is not being performed. This will have a value as
follows:

0 - The feedback source for the position controller will match the drive motor control feedback
source (as specified in menu 3).
1 - Drive feedback source, P1 interface.
2 - Drive feedback source, P2 interface.
3 - Slot 1 position feedback module, P1 interface.
4 - Slot 1 position feedback module, P2 interface.
5 - Slot 2 position feedback module, P1 interface.
6 - Slot 2 position feedback module, P2 interface.
7 - Slot 3 position feedback module, P1 interface.
8 - Slot 3 position feedback module, P2 interface.
11 - Sensorless (the sensorless algorithm estimates position feedback).
This value will be ignored on drives where no encoder input is present.
This object will be read upon a transition from the EtherCAT Pre-operational state to the Safe-
operational state.

If the position feedback encoder configuration is changed then the change will only be
made active upon a module reset or changing the mode of operation (0x6060),
however, if the module is reset to activate the change then a "Sync Task Orun" trip may
be seen.
The value of objects 0x3000 will be ignored on drives which do not support position
feedback.

NOTE

NOTE

«
...
38
39
40
41
42
...
»

Содержание SI-EtherCAT











































































































Отзывы:

Нет отзывов

Похожие инструкции для SI-EtherCAT

Бренд: BandLuxe Страницы: 67

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: Danfoss Страницы: 61

Бренд: Fortinet Страницы: 20

Optane M Series

Бренд: Intel Страницы: 59

Бренд: DAD Страницы: 32

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: RAK Страницы: 30

Surround Dongle

Бренд: Sennheiser Страницы: 18

Бренд: Teknim Страницы: 10

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: CELOT Страницы: 34

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: Maipu Страницы: 19

Бренд: Commell Страницы: 36

Бренд: Intel Страницы: 578

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды