Emerson Rosemount 8800D Series Скачать руководство пользователя страница 103

Страница: 103 / 192

Reference Manual

00809-0100-4772, Rev FA

Troubleshooting

March 2016

Troubleshooting

Install the electronics boards

Verify that power to the flowmeter is off.

Align the sockets on the bottom of the two electronics boards over the pins
protruding from the bottom of the housing cavity.

Carefully guide the sensor cable through the notches on the edge of the circuit
boards.

Slowly press the boards into place. Do not force the boards down. Check the
alignment if they do not glide into place.

Use care to insert sensor cable clip into the electronics board.

Tighten the three captive screws to anchor the two electronics boards. Ensure that
the SST washer is under the screw in the 2o’clock position.

Reinsert jumpers into proper location.

If the meter has the LCD display option, insert the 10-pin header connector into the
LCD display board.

Remove jumpers from the electronics board.

Put the connector through the bezel on the electronics board.

Carefully press the LCD display onto the electronics board.

Tighten the two screws that retain the LCD display.

Insert the alarm and security jumpers in the correct location.

Replace the electronics board compartment cover.

7.5.3

Replacing the F

OUNDATION

Fieldbus electronics housing

The flowmeter electronics housing can be replaced easily when necessary. Use the
following procedure:

Tools needed



in. (4 mm) hex wrench



in. (8 mm) open-end wrench



Screwdriver to disconnect wires



Tools to disconnect conduit (if applicable)

Removing the electronics housing

Turn off the electric power to the flowmeter.

Disconnect the power wires and conduit (if applicable) from the housing.

Use the

in. (4 mm) hex wrench to loosen the housing rotation screws (at the

base of the electronics housing) by turning the screws clockwise (inward) until they
clear the support tube. See

Figure 7-8

See

“Safety messages” on page 81

for complete warning

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание Rosemount 8800D Series

































































































































































































Результаты поиска

Содержание Rosemount 8800D Series

Отзывы:

Похожие инструкции для Rosemount 8800D Series

Бренды по названию

Популярные бренды

Emerson Rosemount 8800D Series, Справочное руководство

Результаты поиска

Содержание Rosemount 8800D Series

Отзывы:

Похожие инструкции для Rosemount 8800D Series

Бренды по названию

Популярные бренды