Emerson Rosemount 8800D Series Скачать руководство пользователя страница 56

Страница: 56 / 192

Reference Manual

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

BASE_TEMP_UNITS

The engineering units of base temperature:

1001 = °C

1002 = °F

Units of 1000 - Kelvins and 1003 - degrees Rankine are also allowed:

1000 = K

1003 = °R

BASE_TEMPERATURE

Base Temperature is the defined temperature at base conditions. Base

temperature is used to calculate the Process Density Ratio.

BLOCK_ALM

The block alarm is used for all configuration, hardware, connection

failure, or system problems in the block. The cause of the alert is entered

in the subcode field. The first alert to become active will set the Active

status in the status parameter. As soon as the unreported status is

cleared by the alert reporting task, another block alert may be reported

without clearing the Active status, if the subcode has changed.

BLOCK_ERR

This parameter reflects the error status of the hardware or software

components associated with a block. The parameter is a bit string, so

multiple errors may be shown.

CAL_MIN_SPAN

CAL_MIN_SPAN is the minimum span that must be used between the

calibration high and low points.

CAL_POINT_HI

CAL_POINT_HI is the value of the primary value measurement used for

the high calibration point.

CAL_POINT_LO

CAL_POINT_LO is the value of the primary value measurement used for

the low calibration point.

CAL_UNIT

CAL_UNIT specifies the units used for the calibration inputs.

CALC_PROC_DENSITY

When the Process Fluid is temperature compensated saturated steam,

this parameter will report the calculated steam density based on the

measured process temperature. The value will be in engineering unit

configured in CALC_PROC_DENSITY_UNITS.

CALC_PROC_DENSITY_UNITS

Calculated process fluid density engineering units.

1097 = kg/m3

1100 = g/cc

1105 = g/liter

1106 = lb/in3

1107 = lb/ft3

COLLECTION_DIRECTORY

The collection directory specifies the number, starting indices, and DD

item IDs of the data collections in each transducer within a transducer

block.

COMPD_K_FACTOR

This parameter represents the K-factor after it has been compensated for

process temperature, materials, installation effects, etc. Units are

reflected in K_FACTOR_UNITS.

COPR_DL_DATA

For factory use only.

COPR_DL_OPT

For factory use only.

COPR_DL_STATUS

For factory use only.

DAMPING

Damping is the sampling period interval to smooth the flow
measurement using a first-order linear filter. Limits are 0.2 to 255

seconds.

ELEC_TEMP_PLOT_LL

100

Electronics Temperature graph plot lower limit which is used in some

host graphical displays.

ELEC_TEMP_PLOT_UL

Electronics Temperature graph plot upper limit which is used in some

host graphical displays.

Table 4-1. Transducer Block Parameters

Parameter

Index

number

Definition

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание Rosemount 8800D Series

































































































































































































Результаты поиска

Содержание Rosemount 8800D Series

Отзывы:

Похожие инструкции для Rosemount 8800D Series

Бренды по названию

Популярные бренды

Emerson Rosemount 8800D Series, Справочное руководство

Результаты поиска

Содержание Rosemount 8800D Series

Отзывы:

Похожие инструкции для Rosemount 8800D Series

Бренды по названию

Популярные бренды