manualshive.com logo in svg

Emerson Rosemount 8800D Series, Справочное руководство

Серия Emerson Rosemount 8800D - это передовое оборудование для измерения потока. Чтобы узнать больше о его функциях и установке, загрузите бесплатное Руководство по эксплуатации с нашего веб-сайта. Посетите manualshive.com, чтобы скачать руководство по использованию и настроить ваш оборудование.

Поделиться
Скачать
background image

137

Product Certifications

Product Certifications

March 2016

Reference Manual

00809-0100-4772, Rev FA

B.5.4  Chinese certifications (NEPSI)

Flameproof certification

GB3836.1 – 2010
GB3836.2 – 2010
GB3836.4 – 2010
GB3836.20 – 2010

E3

Certification No. GYJ12.1493X
Ex ia / d IIC T6 Ga/Gb (Integral Transmitter)
Ex d [ia Ga] IIC T6 Gb (Remote Transmitter)
Ex ia IIC T6 Ga (Remote Sensor)
Ambient temperature range: -50 °C 

≤

 Ta 

≤

 +70 °C

Process temperature range: -202 °C to +427 °C
Power Supply: 42 Vdc Max 4-20 mA HART
Power Supply: 32 Vdc Max Fieldbus
U

m

 = 250V

Special conditions for safe use (X):

1. The maximum allowable length of the 

interconnecting cable between transmitter and 
sensor is 152 m. The cable shall also be provided by 
Rosemount Inc., or by Emerson Process Management 
Flow Technologies Co., Ltd.

2. Suitable heat-resisting cables rated at least +80 °C 

shall be used when the temperature around the cable 
entry e60 °C.

3. Dimensions of flameproof joints are other than the 

relevant minimum or maximum specified in Table 3 of 
GB3836.2-2010. Contact manufacturer for details.

4. The Flowmeter is provided with special fasteners of 

property class A2-70 or A4-70.

5. Any friction should be prevented in order to avoid the 

risk of electrostatic charge on the enclosure due to 
non-conductive paint.

6. The earthing terminal should be connected to the 

ground reliably at site.

7. Do not open when energized.

8. The cable entry holes have to be connected by means 

of suitable entry device or stopping plugs with type of 
protection of Ex d IIC Gb the cable entry device and 
stopping plugs are approved in accordance with 
GB3836.1-2010 and GB3836.2-2010, and which are 
covered by a separate examination certificate, any 
unused entry hole is to be fitted with type of 
protection of Ex d IIC Gb flameproof stopping plug.

9. Users are forbidden to change the configuration to 

ensure the explosion protection performance of the 
equipment. Any faults shall be settled with experts 
from the manufacturer.

10. Precautions shall be taken to ensure that the 

electronic parts are within permissible ambient 
temperature considering the effect of the allowed 
fluid temperature.

11. During installation, operation and maintenance, users 

shall comply with the relevant requirements of the 
product instruction manual, GB3836.13-1997 
“Electrical apparatus for explosive gas atmospheres 
Part 13: Repair and overhaul for apparatus used in 
explosive gas atmospheres”, GB3836.15-2000 
“Electrical apparatus for explosive gas atmospheres 
Part 15: Electrical installations in hazardous areas 
(other than mines)”, GB3836.16-2006 “Electrical 
apparatus for explosive gas atmospheres Part 16: 
Inspection and maintenance of electrical installation 
(other than mines)”, and GB50257-1996 “Code for 
construction and acceptance of electrical device for 
explosion atmospheres and fire hazard electrical 
equipment installation engineering”.

I. S. certification

GB3836.1 – 2010
GB3836.4 – 2010
GB3836.20 – 2010
GB12476.1 – 2000

I3

 

Certification No. GYJ12.1106X
Ex ia IIC T4 Ga (-60 °C 

≤ 

Ta 

≤ 

+ 70 °C) 4-20 mA HART

Ex ia IIC T4 Ga (-60 °C 

≤ 

Ta 

≤ 

+ 60 °C) Fieldbus

FISCO

IH

Certification No. GYJ12.1106X
Ex ia IIC T4 Ga (-60 °C 

≤

 Ta 

≤

 +60 °C)

Special conditions for safe use (X):

1. The maximum allowable length of the 

interconnecting cable between transmitter and 
sensor is 152 m. The cable shall also be provided by 
manufacturer.

2. When transient protection terminal block applied to 

this product, during installation, users shall comply 
with Clause 12.2.4 in GB3836.15-2000 “Electrical 
apparatus for explosive gas atmospheres Part 15: 
Electrical installations in hazardous areas (other than 
mines).”

3. Suitable heat-resisting cables rated at least +80 °C 

shall be used when the temperature around the cable 
entry e60 °C.

4-20 mA HART 

entity parameters

Fieldbus entity 

parameters

FISCO input 
parameters

U

i

= 30 VDC

U

i

= 30 VDC

U

i

= 17.5 VDC

I

i

(1)

1. Total 

for 

transmitter.

= 185 mA

I

i

(1)

= 300 mA

I

i

(1)

= 380 mA

P

i

(1)

= 1.0 W

P

i

(1)

= 1.3 W

P

i

(1)

= 5.32 W

C

i

= 0 

μ

F

C

i

= 0 

μ

F

C

i

= 0 

μ

F

L

i

= 0.97mH

L

i

< 10 

μ

H

L

i

< 10 

μ

H

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание Rosemount 8800D Series

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 8800D Series

Major tech MT350 Instruction Manual preview
MT350
Бренд: Major tech Страницы: 8
Waltron 9072 User Manual preview
9072
Бренд: Waltron Страницы: 25
BANTE inststruments TB100 Instruction Manual preview
TB100
Бренд: BANTE inststruments Страницы: 15
3Bays GSA PUTT User Manual preview
GSA PUTT
Бренд: 3Bays Страницы: 21
Callaway 350TL Manual preview
350TL
Бренд: Callaway Страницы: 13
FARMSCAN Jackal v2 Manual preview
Jackal v2
Бренд: FARMSCAN Страницы: 28
Keithley 236 Service Manual preview
236
Бренд: Keithley Страницы: 138
S.E. International USB Inspector Operation Manual preview
USB Inspector
Бренд: S.E. International Страницы: 30
SZBJ BM5263 Operator'S Manual preview
BM5263
Бренд: SZBJ Страницы: 2
Rabid Elephant NATURAL GATE User Manual preview
NATURAL GATE
Бренд: Rabid Elephant Страницы: 18
Keithley 2651A Quick Start Manual preview
2651A
Бренд: Keithley Страницы: 18
Aethra D2500 Specifications preview
D2500
Бренд: Aethra Страницы: 2
Flymaster Vario LS Quick Start Manual preview
Vario LS
Бренд: Flymaster Страницы: 7
365SMART SM-06-02015R Original Manual preview
SM-06-02015R
Бренд: 365SMART Страницы: 20
UEi MCP4 Instruction Manual preview
MCP4
Бренд: UEi Страницы: 5
Anglerfish Creative Lighting TRIGGER V3.0 User Manual preview
TRIGGER V3.0
Бренд: Anglerfish Creative Lighting Страницы: 15
AVAZZIA Med-Sport OTC Manual preview
Med-Sport OTC
Бренд: AVAZZIA Страницы: 18
PowerMetrix PowerMaster MTA15Z Product Manual preview
PowerMaster MTA15Z
Бренд: PowerMetrix Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды