manualshive.com logo in svg

Emerson Rosemount 8800D Series, Справочное руководство, Страница: 69 / 192

Поделиться
Скачать
Emerson Rosemount 8800D Series Скачать руководство пользователя страница 69

59

Reference Manual 

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

Process conditions

Used to calculate the density ratio. Refer to the equation listed under Density Ratio.

Process temperature

Process Temperature is the absolute temperature T

f

 at actual (flowing) conditions in 

degrees Rankine or Kelvin. The flowmeter electronics will convert from degrees Fahrenheit 
or degrees Celsius to degrees Rankine or Kelvin respectively.

Process pressure

Process Pressure is the absolute pressure P

f

 at actual (flowing) conditions in psia or KPa 

absolute. The flowmeter will convert from the pressures in absolute for the calculation.

Process compressibility

Process Compressibility is the compressibility Z

f

 at actual (flowing) conditions (dimension-

less).

Base conditions

Base Conditions is used to calculate the density ratio. Refer to the equation listed under 
Density Ratio.

Base temperature

Base Temperature is the absolute temperature T

b

 at standard (base) conditions in degrees 

Rankine or Kelvin. The flowmeter electronics will convert from degrees Fahrenheit or 
degrees Celsius to degrees Rankine or Kelvin respectively.

Base pressure

Base Pressure is the absolute pressure P

b

 at standard (base) conditions in psia or KPa 

absolute. The flowmeter will convert from the pressures in absolute for the calculation.

Base compressibility

Base Compressibility is the compressibility Z

b

 at standard (base) conditions (dimension-

less).

4.4.4

Sensor

Pipe I.D.

The Pipe I.D. (inside diameter) of the pipe adjacent to the flowmeter (mating pipe) can 
cause entrance effects that may alter flowmeter readings. Specify the exact inside diameter 
of the pipe to correct for these effects. Enter the appropriate value for this variable.

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание Rosemount 8800D Series

































































































































































































Отзывы:

Нет отзывов