Emerson Rosemount 8800D Series Скачать руководство пользователя страница 85

Страница: 85 / 192

Reference Manual

00809-0100-4772, Rev FA

Analog Input Function Block

March 2016

Analog Input Function Block

Table 6-2. Analog Input Function Block System Parameters

Parameter

Index
No.

Available
values

Units

Default

Read/Write

Description

ACK_OPTION

0 = Auto Ack

Disabled

1 = Auto Ack

Enabled

None

0 all Disabled Read and Write Used to set auto

acknowledgment of alarms.

ALARM_HYS

0 – 50

Percent

0.5

Read and Write The amount the alarm value

must return within the alarm

limit before the associated

active alarm condition clears.

ALARM_SEL

HI_HI, HI, LO,

LO_LO

None

None selected Read and Write Used to select the process

alarm conditions that will

cause the OUT_D parameter to

be set.

ALARM_SUM

Enable/Disable None

Enable

Read and Write The summary alarm is used for

all process alarms in the block.

The cause of the alert is

entered in the subcode field.

The first alert to become active

will set the Active status in the

Status parameter. As soon as

the Unreported status is

cleared by the alert reporting

task, another block alert may

be reported without clearing

the Active status, if the

subcode has changed.

ALERT_KEY

1 – 255

None

Read and Write The identification number of

the plant unit. This information

may be used in the host for

sorting alarms, etc.

BLOCK_ALM

Not applicable None

Not

applicable

Read only

The block alarm is used for all

configuration, hardware,

connection failure or system

problems in the block. The

cause of the alert is entered in

the subcode field. The first

alert to become active will set

the Active status in the Status

parameter. As soon as the

Unreported status is cleared by

the alert reporting task,

another block alert may be

reported without clearing the

Active status, if the subcode

has changed.

BLOCK_ERR

Not applicable

None

Not

applicable

Read only

This parameter reflects the

error status associated with the

hardware or software

components associated with a

block. It is a bit string, so that

multiple errors may be shown.

CAP_STDDEV 40

> = 0

Seconds

Read and Write The time over which the

VAR_INDEX is evaluated.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Содержание Rosemount 8800D Series

































































































































































































Результаты поиска

Содержание Rosemount 8800D Series

Отзывы:

Emerson Rosemount 8800D Series, Справочное руководство, Страница: 85 / 192

Результаты поиска

Содержание Rosemount 8800D Series

Отзывы: