Emerson Liebert PEX+ Series, Руководство пользователя

Страница: 52 / 92

44 Chapter 5 iCOM Controller
Liebert. PEX+Series Precision Air Conditioner User Manual
5.7.8 NETWORK SETUP
The NETWORK SETUP menu is used to set the parameters when the system is in a network subject to the monitoring
of a host. See Table 5-28 for parameter descriptions.
Table 5-28 Descriptions of NETWORK SETUP parameters
Parameters Default Setting range Description
S802 #UNITS 1 1 ~ 32 Range: 1 ~ 32
S803 TEAMWORK No No, 1, 2 Range: No, 1, 2
S824 MON ADD 3 1 ~ 99 Monitoring address No. of the unit
S825 MON T.O. No No, 1, 2 Monitoring Timeout
S825 MON H.S. 3 1 ~ 99 Monitoring Handshake
S830 UPGRSTAT -
None,S CS,
S NS,S SR,
S GDR,
SBLV,SRAM,
Ready,Fail
Lock for Upgrade Status
S830 UPGRADE -
No,Yes,
ULock
Lock for Upgrade
S831 CS CTRL No
Save, Load,
No
Save the parameter set through MON ADD to the iCOM controller.
‘No’ means not saved
S831 CS STAT Change Change, Valid
Indication of the saving state of the parameter set through MON
ADD.
‘Change’ means that the parameter is changed but not saved.
‘Valid’ means that the setting is valid and saved
S832 NW CTRL No
Save, Load,
No
Save the parameter set through U2U GRP to the iCOM controller.
‘No’ means not saved
S832 NW STAT Valid Change, Valid
Indication of the saving state of the parameter set through U2U
GRP.
‘Change’ means that the parameter is changed but not saved.
‘Valid’ means that the setting is valid and saved
S835 MON PROT Vlct4
No,Vlct3,HN,
IGM,n.a.,Vlct4
Host monitoring protocol setting. Range: Vlcty (Velocity uses
intelligent card), HN (Hironet), IGM (ECA2), No
S836 IP #1 192
- Set IP address
S836 IP #2 168
S836 IP #3 254
S836 IP #4 1
S837 NM #1 255
- Set subnet mask
S837 NM #2 255
S837 NM #3 255
S837 NM #4 0
S838 GW #1 0
- Set gateway address
S838 GW #2 0
S838 GW #3 0
S838 GW #4 0
S840 U2U PROT GBP - -
S841 U2U ADD 3 - Group address No. of this unit
S842 U2U GRP 1 - -
S843 BL CTRL No S + R, No
Boot program variant load. Saving the change of S835 ~ S841 needs
the S + R command of this parameter. The system will reset after the
saving, and configure according to the new parameters
S843 BL STAT Valid Change, Valid
Indication of whether or not the parameters set through S835 ~ S841
are saved.
‘Change’ means that the parameter is changed but not
saved.
‘Valid’ means that the setting is valid and saved
S844 SR CTRL No C + R, No
Static RAM data reset control. If the change of S835 ~ S841 are not
saved, using the C + R command in this parameter can restore S835
~ S841 to their original settings, and the system will reset afterwards
S844 SR STAT Valid - STD
SW# - - Version No. of the control software
MAC - - MAC address of the network card of the iCOM controller
NAME UNIT UNIT
Name of the unit. By default: UNIT. You can change the name as
you need