Emerson Copeland Scroll YBVH021 1U-3E9 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 41

Emerson Copeland Scroll YBVH021 1U-3E9 Скачать руководство пользователя страница 23

18

C6.2.38/0719/E

Figure 15: Power cable molded plug (IP65)

Figure 16: Connecting the molded plug power cable to the connection pins

4.2.3 Assembly of the molded plug cable

▪

Make sure to use only R290 qualified and dedicated molded plug power cables with grounding

connection and retainer.

▪

Check that the O-ring on the molded plug connector is in place and not damaged.

▪

Shut off power supply.

▪

Check that the circle fence is clean and dry before connecting the molded plug power cable.

▪

Connect the grounding of the molded plug power cable to the compressor circle fence.

▪

Attach the molded plug connector to the compressor connection pins. Smoothly push the molded

plug connector by hand as far as possible towards the pins. Never use a tool to knock the molded
plug as this could damage the glass inserts of the pins

▪

Secure the connection with the retainer.

4.2.4 Removing the molded plug power cable

▪

Shut off power supply.

▪

Remove the retainer from the connection.

▪

Remove the molded plug connector from the connection pins.

▪

Disconnect the grounding from the compressor circle fence.

NOTE: To select the appropriate molded plug power cables, please refer to the Emerson spare
parts software available at

www.climate.emerson.com/en-gb

«
...
21
22
23
24
25
...
»

Содержание Copeland Scroll YBVH021 1U-3E9










































Отзывы:

Нет отзывов