Emerson Bettis 500 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 102

background image

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

8

Section 2: Quick Start

Quick Start

2.2

Network Setup

This is only applicable if the Controlinc Auxiliary Control Module (ACM) and the
Communication Adapter Module (CAM) are installed and enabled. These instructions
assume all parameters have been set with the exception of the network node address.

1.

Remain in the “

SETUP

” mode.

2.

Select

NEXT

to advance through the displays until “

NETWORK SETUP?

” appears.

3.

Rotate the control knob to

YES

. “

NETWORK NODE ADDRESS XXX

” appears.

4.

Rotate the control knob to

NO

to increment the address numbers. Hold in the

NO

position until the desired address is reached.

NOTE:

If the desired address is a lower number than what is displayed, continue to
increment the numbers until the highest numbered address is reached.
The address numbers will then start with the lowest numbered address
and continue to increment.

5.

When the correct address is displayed, rotate the control knob to

YES

.

2.3

Check Settings

1.

Operate the valve to the fully close position.

2.

Verify the green LED is ON (default setting) and 0% is displayed.

3.

Operate the valve to the fully open position.

4.

Verify the red LED is ON (default setting) and 100% is displayed.

«
...
14
15
16
17
18
...
»

Содержание Bettis 500







































































































Отзывы:

Нет отзывов

Похожие инструкции для Bettis 500

Бренд: Eaton Страницы: 86

Бренд: Value Point Страницы: 7

Бренд: Daikin Страницы: 5

Бренд: Datavideo Страницы: 8

Бренд: J3C Страницы: 2

Бренд: Olsberg Страницы: 68

Бренд: D+H Страницы: 32

Бренд: DeLaval Страницы: 102

Бренд: FrSky Страницы: 2

Бренд: Baby Trend Страницы: 22

Q.PEAK DUO XL-G11S.X / BFG Series

Бренд: Qcells Страницы: 26

Бренд: EpiSensor Страницы: 37

Бренд: Potter Страницы: 25

Turbo-V 250 series

Бренд: Varian Страницы: 79

Бренд: M-system Страницы: 7

Бренд: Cypress Страницы: 2

Бренд: Dudley Страницы: 8

PLATINUM PS-9003

Бренд: HydroQuip Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды