Emerson Bettis 500 Скачать руководство пользователя страница 81

Страница: 81 / 102

Installation and Operation Manual

E2K-405-0218 Rev. 2

February 2018

Section 6: Troubleshooting

Troubleshooting

6.2

Display Diagnostics

Displaying diagnostics retrieves historical data that is stored in the actuator’s memory.
This aids in troubleshooting.

At the “

DISPLAY DIAGNOSTICS?

” prompt, answer “

YES.

”

Use the selector knob (NEXT/BACK) to review the settings. See

Figure 6-1

NOTE:

When the “SET LIMITS BEFORE OPERATING” alarm is displayed, no other alarms will be
displayed until the limits are set.

Figure 6-1

Display Diagnostics

YES

BACK

Figure 6-1Display

Diagnostic

Display

Alarm

Log?

YES

NEX

DISPLAY

HARDWARE

DIANOSTICS?

EXIT?

Go to

Figure 6-2

Go to next display.

See Figure 5-1

NO
OR

NEXT

YES

Display

Torque

Profile?

Go to

Figure 6-3

YES

Display

Torque

Archive?

Go to

Figure 6.2.3

YES

Display

Operate

Log?

Go to

Figure 6-4

YES

Display

Operate

Archive?

Go to

Figure 6-5

YES

Display

Hardware

State?

Go to

Flowchart 6-6

Содержание Bettis 500







































































































Результаты поиска

Содержание Bettis 500

Отзывы:

Emerson Bettis 500, Инструкция по установке и эксплуатации, Страница: 81 / 102

Результаты поиска

Содержание Bettis 500

Отзывы: