Emerson Bettis 500 Скачать руководство пользователя страница 21

Страница: 21 / 102

Installation and Operation Manual

E2K-405-0218 Rev. 2

February 2018

Section 3: Installation

Installation

Figure 3-3

Control Terminal Connections

Figure 3-4

Power Terminal Connections

3.3.4 Cable Connections

Connect the main power supply cables, including the earth/ground wire
using #1 Phillips or 3/16 inch (5mm) slotted tip screwdriver.

Attach earth/ground wire to internal ground lug using 1/4 inch #11
slotted screwdriver.

Use the barrier strip clamp screws to connect the control wires.

Ensure all connections are hand tight, including any unused
terminal connections.

The main power supply and ground wire connections are screw size M4.
The control connection screw size is M3.

3.3.5 Replace Terminal Compartment Cover

To replace the cover, follow the steps detailed in

Section 3.3.1, Remove Separate

Terminal Chamber (STC) Cover

in reverse order.

NOTE:

Clean electrical enclosure threads thoroughly and lightly grease with a dielectric
grease before closing.

3.3.6 External Earth/Ground Connections

External connection points are provided on the actuator motor and main gear
housing for attaching earth/ground in accordance with local electric codes for
installation cables.

Connect the external earth/ground connection as follows:

Using a 1/4 inch (6mm) slotted tip screwdriver back out the 5/16 inch
(8mm) set screw.

Connect 14 AWG or larger earth/ground wire; tighten setscrew.

Содержание Bettis 500







































































































Результаты поиска

Содержание Bettis 500

Отзывы:

Похожие инструкции для Bettis 500

Бренды по названию

Популярные бренды

Emerson Bettis 500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Bettis 500

Отзывы:

Похожие инструкции для Bettis 500

Бренды по названию

Популярные бренды