Installation and Operation Manual
E2K-405-0218 Rev. 2
February 2018
77
Section 6: Troubleshooting
Troubleshooting
6.2.5 Display Operation Archive
Operation archive displays operation data from the initial commissioning.
See
Figure 6-5
. The operation archive cannot be reset in the “
CHANGE SETTINGS
”
mode. The operation archive can be reset in the “
FACTORY SETUP
” mode;
however the actuator must be decommissioned and travel limits must be reset
before operating as detailed in
Section 4.3.1, Setting Position Limits
.
1.
At the “
DISPLAY OPERATE ARCHIVE
” prompt, answer “
YES.
“
2.
Use the control knob (
YES
) to review the operation archive.
Figure 6-5
Display Operation Archive
6.2.6 Display Hardware
This display reports the status of the modules and can identify which module is at
fault if a problem exists with the actuator. Typical status report can include:
•
Normal
•
Not Configured
•
Lost Link
•
Failed
1.
At the “
DISPLAY HARDWARE?
” prompt, answer “
YES.
”
2.
Use the control knob (
YES
) to review the hardware status.
See
Figure 6-6
.
NO
YES
YES
NO
YES
YES
NO
Analog
<analog_state>
<state: NORMAL/
NOT CONFIGURED/
UNDER RANGE/
OVER RANGE>
Network
<network_state>
<state: NORMAL/
NOT CONFIGURED/
SPI LINK LOST/ACM
FAILED/HOST LOST
EFM
<efm_state>
<state: NORMAL/
SHUTDOWN/
FAILED>
Refresh every
30 seconds
BACK
YES
DISPLAY
ALARM LOG?
DISPLAY ALARM LOG
Figure 6-2
Go to
Figure 6-1
DISPLAY TORQUE PROFILE
Figure 6-3
NO
OR
NEXT
NO
OR
NEXT
BACK
NEXT
NO
NO
YES
1 <alarm 1>
2 <alarm 2>
YES
YES
DISPLAY
TORQUE PROFILE
Pull-out
Torque
<xx>%
YES
3 <alarm 3>
4 <alarm 4>
NO
YES
5 <alarm 5>
6 <alarm 6>
NO
YES
7 <alarm 7>
8 <alarm 8>
NO
YES
9 <alarm 9>
10 <alarm 10>
YES
DISPLAY
OPERATE LOG?
DISPLAY OPERATION LOG
Figure 6-4
DISPLAY HARDWARE
Figure 6-6
NO
OR
NEXT
BACK
NEXT
NO
NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
YES
BACK
NEXT
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Profile?
YES
NO
YES
NO
YES
YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Profile?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
NO
OR
NEXT
YES
Pull-out
Torque
<xx>%
YES
BACK
NEXT
NO
NO
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Archive?
YES
NO
YES
NO
YES
YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Archive?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
DISPLAY
TORQUE ARCHIVE
NO
OR
NEXT
YES
REMOTE
DISPLAY#2
<rem_disp#2_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK/FAILED>
YES
BACK
NEXT
NO
NO
NO
NO
NO
YES
APD Module
<apd_state>
<state: NORMAL/
FAILED>
Inside
Temperature=
<xx>C
YES
NO
YES
YES
NO
DISPLAY
HARDWARE?
EXIT?
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hr:min:sec>
YES
DISPLAY
OPERATE ARCHIVE?
DISPLAY OPERATION ARCHIVE
Figure 6-5
NO
OR
NEXT
BACK
NEXT
NO
NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hours>
Central Control
<cen_ctrl_state>
<state: NORMAL/
LOST LINK /FAILED>
Local Display
<lcl_disp_state>
<state: NORMAL/
LOST LINK /FAILED>
REMOTE
DISPLAY#1
<rem_disp#1_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK / FAILED>
