Emerson Bettis 500 Скачать руководство пользователя страница 18

Страница: 18 / 102

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

Section 3: Installation

Installation

Unscrew

Locknut

(piece #55) while holding

Bronze Stem Nut

(piece #54) or Steel

Bore and Key Bushing. Remove the

Stem Nut

and

Key

(piece #52).

Lubricate

Stem

. Run

Stem Nut

(piece #54) down

Stem

to verify Acme thread fit.

Remove

Stem Nut

(piece #54) and set aside.

Model 3000-8000 may include thrust base assemblies. See

Appendix

for instructions.

3.2

Mechanical Installation onto the Valve

Lower actuator over

Stem

onto valve flange.

Insert the screws through the valve flange into the actuator and engage at least
one full screw diameter deep into the bottom base.

Tighten to a preload.
See

Appendix

for common bolt tightening torques.

NOTE:

Mounting screws are provided only if Emerson supplied the adapter. Verify screws are
through the adapter; engage a minimum of one screw diameter deep into the actuator
base.

Screw the

Stem Nut

(piece #54) onto the

Stem

until it enters the

Drive Sleeve

Place Key (piece #52) in line with the

Drive Sleeve Keyway

. Insert

Key

(piece #52).

Turn the handwheel in the Open direction to pull the

Stem Nut

(piece #54) into

the

Drive Sleeve

until it bottoms out.

NOTE:

Valve will begin to open.

Place the

Locknut

(piece #55) over the

Valve Stem

. Screw the

Locknut

(piece #55) firmly into place against the top of the

Stem Nut

(piece #54)

using a drift to tighten.

Use a number 30 (0.1285) drill bit: drill a hole 3/4 inch (19mm) deep into the

Drive Sleeve

assembly threads for the Locknut Lockpin (piece #56).

Use the groove in the

Stem Nut Locknut

threads as a guide.

Install

Locknut Lockpin

(piece #56) into drilled hole to prevent the

Stem Nut Locknut

(piece #55) from working loose and turning.

NOTE:

When installing, the

Locknut Lockpin

(piece #56) should extend 1/4 inch (6mm) inch

above the

Drive Sleeve

assembly to allow for easy removal.

CAUTION:

Locknut must be screwed very tightly against stem nut.

Содержание Bettis 500







































































































Результаты поиска

Содержание Bettis 500

Отзывы:

Бренды по названию

Популярные бренды

Emerson Bettis 500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Bettis 500

Отзывы:

Бренды по названию

Популярные бренды