background image

EMC

®

 SVR-I1U-1304 Server Installation and

Maintenance Guide

P/N 300-013-263
REV 02

May, 2013

This document describes installation and maintenance procedures for the SVR-I1U-1304
server. This server has slots for four 3.5-inch drive assemblies. Some server components
are replaceable as field replaceable units (FRUs). Refer to your product documentation for
information on which components are FRUs. Before attempting to perform hardware service
procedures, review your service contract because replacement of some server components
by unauthorized personnel may void service warranties.
Topics include:

u

Technical information and requirements

.................................................................... 2

u

Installing the server in a cabinet

.................................................................................3

u

Maintaining the server

............................................................................................. 14

u

Handling field replaceable units (FRUs)

....................................................................14

u

Replacing a disk drive assembly

.............................................................................. 15

u

Replacing the server

.................................................................................................18

u

Removing the slide rails from the cabinet

.................................................................27

Содержание SVR-I1U-1304






























Отзывы: