28
Use the
R
button to cancel the last character entered. Press
to
confirm the change. When the change is confirmed, the message “Done!”
will appear. During this procedure, a “notes” function can be used to help
with duplication of the codes. With changes mode currently active and no “?”
symbol displayed, press the
button to record the sequence entered.
To exit changes more, press
or
.
Select another device, access changes mode by pressing the
button,
then press
to replace the existing sequence with the sequence
recorded in the notes. Press
to confirm the change.
5.0 - CLOCK
The clock must be programmed so that the service can be implemented
correctly. Should the electronic unit remain switched off, the date and time
will remain stored for at least 2 days. When the clock is first powered up,
or when the electronic unit remains switched off for longer than 2 days, the
date is set to 1 January 2013 and the time to 00:00.
The clock can be set from the keypad. Press the
button, the editable
field is indicated by a solid rectangle to the right:
To change the day, enter the requisite numbers
0
+
..
9
WXYZ
with the keypad,
then move on to the month or year, using the
button which shifts the
editable field to the right. To move to the left, use
. When done, confirm
with
.
If the values are correct the display then shows:
If there is an error, for example if the day is set as 58, changes
are rejected and the rectangle moves to the position of the error:
There is no need to enter the day of the week, as this will be calculated
automatically from the date.
5.1 - ENABLE TIMED CODES
The service must be configured and then activated by means of this
procedure. If necessary, the service can be deactivated (even after configu-
ration), suspending only the actual service while retaining all the program-
ming data needed for its operation.
To enable, press
1
: the message ENABLE TIMED CODES, (YES)
confirm with
. When confirmed, the message “DONE” will appear.
To disable the service, press
0
+
and confirm with
.
When confirmed,
the message “DONE” will appear.
Default = No
5.2 - FIRST TIMED CODE
This configuration specifies the first code to be used for the Timed Codes
function.
Enter the number with buttons
0
+
..
9
WXYZ
EHWZHHQDQG>@
To cancel the configuration, enter 0 and confirm with
:
,IWKHFRGHQXPEHULVRXWVLGHWKHUDQJH>@WKHHUURUZLOOEH
indicated by the message “OVER LIMIT”.
If the first code is higher than the second, or if one is programmed and the
other is not, a warning to check the other code is displayed:
The valid codes are those in which the number ranges from the first to the
last indicated, inclusive
5.3 - LAST TIMED CODE
Similar to the code described above, but referring to the last valid code.
5.4 - CODE VALIDITY TIME BANDS
As mentioned previously, there are two time bands for Monday to Friday,
and two for Saturday and Sunday. The default setting is no configuration,
and all start and end values are set at 00:00
The end must be higher than the start, otherwise the configuration will not
EHYDOLG)RUH[DPSOHVWDUWWLPH DQGHQGWLPH ZRXOGQRWEH
YDOLGDQGQHLWKHUZRXOGVWDUWWLPH DQGHQGWLPH
To change the time, press
: BAND 1 MON / FRI - START = 00:00
A double arrow appears on the right, indicating that buttons
and
can be used to adjust the time by increments of 30 minutes.
Alternatively, use the
0
+
..
9
WXYZ
buttons to set the time:
If need be, buttons
and
can be used to set the minutes:
Confirm with
:
with the confirmation step complete, the message “DONE” will appear.
5.5 - CHANGE INDOOR UNIT CONFIGURATIONS
For each indoor unit installed in the system, it is possible to configure
operating options grouped in four segments: “Flags”, “Programmable
buttons”, “Call groups” and “Landing call”. Certain indoor units have a
fifth segment, namely audio/video levels. To carry out this procedure, the
devices being programmed (indoor units) must be connected to the system
and identified with a code. The electronic unit searches the first device
(indoor unit), identified by physical code 1, and analyzes the type. Use the
EXWWRQVWRVHOHFWRQHRIWKH>@GHYLFHV,IWKH,'FRGHLV
known, enter the number and press the
button to select it.
Having located the required device, press the
button to access change
configuration mode. The configuration options vary according to the type of
device. With changes mode activated, use the
,
and
R
buttons
to navigate the parameters, and the
button to confirm any changes
made. Line 1 of the display will show the current parameter, and line 2 the
value assigned to it.
