21
ENGAGED - PLEASE WAIT MESSAGE
When the message ENGAGED appears in the display, the electronic unit
is disabled from making calls, as another call from another electronic unit
is in progress. If a call is attempted with the ENGAGED message currently
displayed, the electronic unit emits a continuous warning beep.
MUTE RINGTONE FUNCTION (INDOOR UNIT)
If a call is made to an indoor unit with the “ringtone muted” function active,
the electronic unit will generate a beep through the loudspeaker and di-
splay the message “Do not disturb”, to indicate that a call cannot be made
currently to the user.
SELF-START
display the message “ENGAGED”.
If a call is made in this situation, the effect will be to
cancel the self-start
procedure
.
LOCK RELEASE FROM ENTRANCE PANEL
The lock of an electronic unit can be operated if one of 1000 codes, each
comprising 8 digits, is known beforehand. Before entering the code digits,
the preset access code must be entered, as described under heading 1.4:
In the meantime, the first line of the display shows the active buttons.
Enter all code digits:
Pressing
the system checks whether or not the code already exists. If
it does, the local lock is activated. In the event of error, there is no warning.
If a mistake is made when entering data, press
R
and start again.
OPENING F1 FROM ENTRANCE PANEL
The F1 output of an electronic unit can be operated if one of 1000 codes,
each comprising 8 digits, is known beforehand. Before entering the digits
of the code, the access code must be provided by pressing
R
+
2
ABC
:
In the meantime, the first line of the display shows the active buttons..
Enter all code digits:
Pressing
, the system checks whether or not the code already exists. If
it does, the local F1 output is activated. In the event of error, there is no war-
ning. If a mistake is made when entering data, press
R
and start again.
OPENING F2 FROM ENTRANCE PANEL
The F2 output of an electronic unit can be operated if one of 1000 codes,
each comprising 8 digits, is known beforehand. Before entering the digits of
the code, the access code must be provided by pressing
R
+
3
DEF
:
In the meantime, the first line of the display shows the active buttons.
Enter all code digits:
Pressing
the system checks whether or not the code already exists.
If it does, the local F2 output is activated. In the event of error, there is no
warning.
Note
: Some codes can be employed only during certain time bands.
ADJUSTING VOLUME DURING CONVERSATION
BOTH the internal and the external volume can be adjusted during a con-
versation. The adjustments can be made only after enabling the function,
as described below.
- Press
buttons
R
and
5
JKL
simultaneously, or alternatively, press and
hold the
R
button, then press the
5
JKL
button.
- When the following messages are displayed in alternation
enter the parameter programming password; the default password is
6
MNO
5
JKL
4
GHI
3
DEF
2
ABC
1
- Every time a button is pressed there will be a short “beep”, an asterisk “*”
appears on the display, and there are a further 25 seconds (timeout) in
which to press the next button. If the timeout is allowed to elapse without
pressing any button, the electronic unit will exit programming mode.
- After entering the password, press the
button to activate the fun-
ction. If the password is correct, the electronic unit will briefly display the
message: VOLUME CONTROL MODE ACTIVE.
Once the function is enabled, when the next call is answered, the following
messages appear cyclically on the display
Use the
buttons to raise or lower the external volume. To save
the selected volume, press
. When the setting is stored in the memory,
a message “Done” will appear.
Pressing the
button, selection of the INTERNAL VOLUME IS
ENABLED.
Likewise in this instance, use the
buttons to select the internal
volume and press
to store the setting. Pressing the
button again,
the external volume control function reappears. At the end of the conserva-
tion, which is terminated by replacing the handset or when the conversation
timeout elapses or if the
R
button of the electronic unit is pressed, the
volume control function is cancelled.
TRADITIONAL BUTTONS
Up to two 12TS button modules or one 12TD button module can be con-
nected for calls directed to a specific user or operator (see heading 1.5,
