ELTRA CS-580A Скачать руководство пользователя страница 52

Страница: 52 / 70

7.8 Lance replacing

DANGER

D10.0005

Mortal danger from electric shock

Exposed power contacts - High Voltage

−

An electric shock can cause injuries in the form of burns and cardiac

arrhythmia, respiratory arrest or cardiac arrest.

•

Set the mains switch of the analyzer to position 0 and pull the
mains plug of the mains socket.

CAUTION

C12.0076

Scalding/burns

Hot furnace / combustion tube / analyzer parts

−

Parts of the analyzer can be very hot.

•

Wait before start working until the analyzer is cooled down.

•

Switch off the analyzer and disconnect the power plug.

•

Remove the cover panel (1) of the cabinet. Unscrew 4 screws (2) on
top.

•

Remove the tubes (3), (4) and (5) from the upper furnace closure
assembly (6/7).

•

Remove the 4 screws (8) which hold the assembly (6/7) on the
furnace.

•

Lift the assembly (6/7) in straight vertical direction.

•

Unscrew the four screws and nuts which hold the parts (6) and (7)
together.

•

Replace the lance (11)

•

Replace the O-ring (10)

•

Replace the O-ring (9)

•

Do reassembling in reverse order

Содержание CS-580A







































































Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды

ELTRA CS-580A, Руководство пользователя

Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды