ELTRA CS-580A Скачать руководство пользователя страница 11

Страница: 11 / 70

The glass tubes must be empty.

3.2 Transport

NOTICE

N1.0075

Transport

−

Mechanical or electronic components may be damaged.

•

The device must not be bumped, shaken or thrown during transport.

•

The device must be transported upright

3.3 Conditions for the Installation Site

Requirements regarding the operating conditions:
–

For indoor use only.

–

Operation up to max. 2,000 m above sea level.

–

Ambient temperature of between 5°C and 40°C.

–

Maximum relative air humidity < 80 % (at ambient temperatures

≤ 31°C), with linear

decrease up to 50% relative air humidity at 40

C, non-condensing.

–

A residual current operated device (RCD, 30 mA).

–

An exhaust system to evacuate the combustion gases is strongly recommended.

WARNING

Provide an external fuse (20 ampere, B-type) and a residual current device when

connecting the mains lead to the mains in accordance with the regulations at the installation
site.
–

Information about the required voltage and frequency of the device can be found on the
type plate .

–

The data listed must be consistent with the existing power supply system.

–

The device may only be connected to the power supply system using the connecting lead
supplied.

NOTICE

N2.0022

Electrical connection

Failure to heed the data on the type plate

−

Electronic and mechanical components may be damaged.

•

Only connect the device to a power supply system that is consistent
with the data on the type plate.

–

Fluctuations of the mains supply voltage up to ± 10 %.

–

The device must be operated in accordance with overvoltage category II and pollution
category 2, DIN EN 61010-1.

–

Industrial environment in accordance with DIN EN 61010-1

Содержание CS-580A







































































Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды

ELTRA CS-580A, Руководство пользователя

Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды