ELTRA CS-580A Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 70

background image

51

•

Switch off the analyzer and disconnect the power plug.

•

Remove the cover panel (1) of the cabinet. Unscrew 4 screws (2) on
top.

•

Remove the tubes (3), (4) and (5) from the upper furnace closure
assembly (6/7).

•

Remove the 4 screws (8) which hold the assembly (6/7) on the
furnace. The 4 screws and nuts holding the disk (7) on the part (6)
should remain in place.

•

Lift the upper furnace closure. The assembly consisting of the parts
(6), (7), (9), (10) and (11) is then taken out of the furnace. Take care
to lift it in straight vertical direction to avoid collision of the lance (11)
with the combustion tube (12). If the assembly is not free to be easily
lifted, slightly tilt it carefully in different directions until it becomes free.

•

Unscrew the 4 screws (13) by holding the ring (14) to prevent the
combustion tube (12) from falling down.

•

Remove the ring (14).

•

Remove the O-ring (15). If this O-ring and the combustion tube
remained in the furnace after lifting the assembly (6/7), take care to
prevent the combustion tube from falling down out of the furnace. This
can be done by keeping one hand underneath the furnace or by
supporting the ring (14) with two manually driven screws (13).

•

Lift the combustion tube (12) out of the furnace top. Lift it in straight
vertical direction to avoid collision with the heating elements.

•

Place a new O-ring (9) on a new combustion tube (12).

•

Reinstall in reverse order.

NOTICE

Enter the new combustion tube very carefully in straight vertical direction to avoid collision with
the heating elements.

«
...
49
50
51
52
53
...
»

Содержание CS-580A







































































Отзывы:

Нет отзывов

Похожие инструкции для CS-580A

Бренд: UEi Страницы: 4

Бренд: Aaronia Страницы: 47

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Oceanic Страницы: 17

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Clavinova CLP-110

Бренд: Yamaha Страницы: 46

Clavinova CLP-110

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 8

Бренд: Keeler Страницы: 68

Бренд: E-Mon Страницы: 72

Бренд: Environmental Express Страницы: 40

Бренд: Cal Test Electronics Страницы: 12

Бренд: Rubicson Страницы: 4

SensoControl ServiceJunior

Бренд: Parker Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды