ELTRA CS-580A Скачать руководство пользователя страница 21

Страница: 21 / 70

5.3.2 Autoloader Setup

If the Helios analyser was delivered out an autoloader system, it is configured to be used in automatic mode.
In this case, please install the front cover plate (article number 35400-2001).

5.4 Mains power Connections

DANGER

D3.0005

Mortal danger from electric shock

Exposed power contacts - High Voltage

−

An electric shock can cause injuries in the form of burns and cardiac

arrhythmia, respiratory arrest or cardiac arrest.

•

Set the mains switch of the analyzer to position 0 and pull the
mains plug of the mains socket.

DANGER

D4.0005

Mortal danger from electric shock

Damaged power cable

−

An electric shock can cause injuries in the form of burns and cardiac

arrhythmia, respiratory arrest or cardiac arrest.

•

Never use a damaged power cable to connect the device to the main.

•

Check the power cable and the plug for any damage before use.

NOTICE

Installation of the machine

–

It must be possible to disconnet the machine from the mains at any time.

•

Install the machine such that the connection for the mains cable is
easily accessible.

Содержание CS-580A







































































Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды

ELTRA CS-580A, Руководство пользователя

Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды