ELTRA CS-580A Скачать руководство пользователя страница 38

Страница: 38 / 70

6.3 Applications

DANGER

D7.0006

Danger caused by scalding by samples

Sample material

– Damage to the respiratory tracts, skin and/or mucous membranes.
– Radiation damage.

•

The user must himself assess the risk emanating from a sample during
the analysis.

DANGER

D8.0006

Toxic atmosphere

Sample material

– Acute poisoning by gases from combustion.

•

The user must himself assess the risk emanating from a sample during
the analysis.

•

The analyser must be connected to a exhaust system.

•

The exhaust system must be in operation.

This chapter describes the operation modes for analysis of different sample materials. For
further materials contact the manufacturer.

NOTICE

The maximum weights of the samples should not be exceeded!

6.3.1 Coal

Temperature 1350°C

Weight

300mg-500mg (Depending on the sensitivity of the IR cell and on the C- and
S-content of the sample.)

6.3.2 Calcium Carbonate

NOTICE

Calcium carbonate can be used for calibration in the range of 12% C.

Temperature higher than 1000 °C

Weight

100mg-500mg (Depending on the sensitivity of the IR-cell.)

6.3.3 Graphite

NOTICE

Analysers with a range of 100% C can be calibrated with graphite.

Temperature higher than 1000 °C

Weight:

250mg

Содержание CS-580A







































































Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды

ELTRA CS-580A, Руководство пользователя

Результаты поиска

Содержание CS-580A

Отзывы:

Похожие инструкции для CS-580A

Бренды по названию

Популярные бренды