manualshive.com logo in svg

ELTEX TAU-36.IP, Руководство по эксплуатации

Поделиться
Скачать
ELTEX TAU-36.IP Скачать руководство пользователя страница 70

_________________________________________________________________________________ 

_________________________________________________________________________________ 

70                                           TAU-72.IP/TAU-36.IP Universal Network Terminal 

1.

 

To use a local DNS, leave DNS field in 

'Network/Network settings'

 tab blank or enter the value 127.0.0.1. 

2.

 

In 

'Network/Hosts'

 tab, enter the mapping of a host (SIP domain) to actual IP addresses of SIP proxy/SIP 

registrar. 

3.

 

In 

'PBX/SIP-H323 Profiles/Profile 

n

/SIP Custom'

  tab, specify domains for each pair of SIP proxy and SIP 

registrar. 

4.

 

Enable  routing  via  SIP  proxy  by  selecting 

outbound

  checkbox  in 

'PBX/SIP-H323  Profiles/Profile 

n

/SIP 

Custom'

 tab, or entering prefixes in '

PBX/SIP-H323 Profiles/Profile 

n

/Dialplan (Dialplan table)' tab. 

If you 

configure prefixes, select SIP proxy protocol in 

'Protocol&Target'

 field. 

5.1.2.2.4

 

Codecs Configuration (Profile N Codecs)

 

In 

'Profile n

/

Codecs'

 submenu, you may configure codecs used in the current profile. 

TAU signal processor encodes analogue voice traffic and fax/modem data into digital signal and performs 

its reverse decoding. Gateway supports the following codecs: G.711A, G.711U, G.729, G723.1, G.726-32. 

G.711 is PCM codec that does not employ a compression of voice data. This codec must be supported by 

all VoIP equipment manufacturers. G.711A and G.711U codecs differ from each other in encoding law (А-law is a 
linear  encoding  and  U-law  is  non-linear).  The  U-law  encoding  is  used  in  North  America,  and  the  A-law 
encoding—in Europe. 

G.723.1 is a voice data compression codec, allows for two operation modes: 6.3kbps and 5.3kbps. G.723.1 

codec has a voice activity detector and performs comfort noise generation at the remote end during period of 
silence (Annex A).  

 

G.723.1  codec is  used  together  with  'Silence  compression'  setting.  When  the  setting is  enabled, 
Annex A support is enabled, otherwise it is disabled. 

G.726-32  is  a  voice  data  compression  codec  that  uses  ADPCM  compression  algorithm  at  the  rate  of 

32kbps. 

G.729  is  also  a  voice  data  compression  codec  with  the  rate  of  8kbps.  As  with  G.723.1,  G.729  codec 

supports voice activity detector and performs comfort noise generation (Annex B). 

T.38 is a standard for sending facsimile messages in real time over IP networks. Signals and data sent by 

the fax unit are copied to T.38 protocol packets. Generated packets may feature redundancy data from previous 
packets that allows to perform reliable fax transmissions through unstable channels. 

 

You  don't  have  to  reboot  the  gateway  in  order  to  apply  codec  settings.  
When applying settings, all current calls will be terminated!!! 

In 

'Codecs  configuration'

  section,  you  may  select  codecs  and  an  order  of  their  usage  on  connection 

establishment. Codec with the highest priority should be placed in top position.  Click the left mouse button to 
highlight the row with the selected codec. Use arrow buttons 

(up, down) to change the codec priority. 

—

 

Use G.711A

—use G.711A codec. 

—

 

Use G.711U

—use G.711U codec. 

—

 

Use G.723

—use G.723.1 codec. 

Содержание TAU-36.IP














































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды