Elsner 70184 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

background image

25

Setting parameters

KNX TH65-AP thermal hygrometer

• Version: 27.01.2020 • Technical changes and errors excepted.

Configure a block for the humidity control using the blocking object.

Controller setpoint

If the setpoint is set via parameters:

Set the setpoint for humidity.

If the setpoint is set via communication object:

A starting setpoint is defined as well as a range in which the setpoint may vary.

In "Humidification and dehumidification" control mode, a dead zone is specified so that
no direct changeover switching between humidification and dehumidification is
possible.

Humidification starts when the relative air humidity is below or equal to the setpoint -
dead zone value.

Behaviour of the blocking object with value

• 1 = Block | 0 = release
• 0 = block | 1 = release

Blocking object value
before first call

0 • 1

Specified setpoint using

Parameter • Communication object

Specified setpoint using

Parameter

Setpoint in %

0 … 100

Specified setpoint using

Communication object

The last communicated value
should

• not be retained
• be retained after power restoration
• be retained after power restoration and
programming (not to be used for
first commissioning)

Start setpoint in %
valid until first call

(only if the last retained value is "not"
retained, or retained "after power restora-
tion")

0 … 100

Type of setpoint change

• Absolute value
• Increase / Decrease

Interval

(only when "increasing/decreasing")

0.1°C • 0.2°C • 0.3°C • 0.4°C • 0.5°C • 1°C •
2°C • 3°C • 4°C • 5°C

Dead zone between humidification and
dehumidification in %

(only if both humidification and dehumidifi-
cation are used)

0…50; 10

«
...
25
26
27
28
29
...
»

Содержание 70184





































Отзывы:

Нет отзывов

Похожие инструкции для 70184

Бренд: D-tect Systems Страницы: 19

BLITZFIRE Series

Бренд: Task Force Tips Страницы: 20

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: Burkert Страницы: 192

Бренд: Garmin Страницы: 22

Бренд: Magtrol Страницы: 76

Бренд: Flexim Страницы: 160

Бренд: Neriox Страницы: 10

MultiScanner HD800 OneStep

Бренд: Zircon Страницы: 2

Бренд: HERON Страницы: 2

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

KLIMA GUARD 30.5010

Бренд: TFA Страницы: 22

Бренд: Labom Страницы: 6

Бренд: KRAL Страницы: 48

Бренд: Dairymaster Страницы: 14

Бренд: dynasonics Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды