Elsner 70184 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

background image

15

Setting parameters

KNX TH65-AP thermal hygrometer

• Version: 27.01.2020 • Technical changes and errors excepted.

Threshold value setpoint using parameter:

Set the threshold values and hysteresis directly.

Threshold value setpoint using a communication object:

Beforehand, enter how the threshold value will be received from the bus. Basically, a
new value can be received, or simply a command to increase or decrease.

During initial commissioning, a threshold value must be defined which will be valid un-
til the first call with a new threshold value. For units which have already been taken into
service, the last communicated threshold value can be used. Basically, a temperature
range is given in which the threshold value can be changed (object value limit).

A set threshold value will be retained until a new value or a change is transferred. The
current value is saved in EEPROM, so that this is retained in the event of a power sup-
ply failure and will be available once the power supply is restored.

Switching output

Set the behaviour of the switching output when a threshold value is exceeded/under-
cut. The output switching delay can be set using objects or directly as a parameter.

Threshold value setpoint using

Parameter

• Communication objects

Temperature:

Threshold value in 0.1°C

Humidity:

Threshold value in % RH

-300 … 800; 200
0...100; 70

Hysteresis of the threshold value in %

0 … 50; 20

Threshold value setpoint using

Parameter •

Communication objects

The last communicated value should

• not be retained
• be retained after power restoration
• be retained after power restoration and
programming

Start threshold value

Temperature:

in 0.1°C

Humidity:

in % RH

valid until first call

-300 … 800; 200
0...100; 70

Type of threshold value change

Absolute value • Increase/decrease

Interval

(upon increase/decrease change)

Temperature:

0.1°C • ... • 1°C • ... • 5°C

Humidity:

1% • 2% • 5% • 10%

Hysteresis of the threshold value in %

0 … 50; 20

When the following conditions apply,
the output is
(TV = Threshold value)

• TV above = 1 | TV - Hyst. below = 0
• TV above = 0 | TV - Hyst. below = 1
• TV below = 1 |TV + hysteresis above = 0
• TV below = 0 |TV + hysteresis above = 1

Switching delay from 0 to 1

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching delay from 1 to 0

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

«
...
15
16
17
18
19
...
»

Содержание 70184





































Отзывы:

Нет отзывов

Похожие инструкции для 70184

Бренд: Kane Страницы: 12

Бренд: Medeli Страницы: 14

Бренд: Igema Страницы: 30

Бренд: z-laser Страницы: 62

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: WAGER Страницы: 36

Бренд: Pasco Scientific Страницы: 11

Бренд: Flytec Страницы: 2

Monitoring System 500 II DC

Бренд: Didactum Страницы: 2

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: Oldham Страницы: 96

Vigilantplant NFBU200-S Series

Бренд: YOKOGAWA Страницы: 24

Бренд: horiba Страницы: 117

Бренд: Sequid Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды