Elsner 70184 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

background image

14

Setting parameters

KNX TH65-AP thermal hygrometer

• Version: 27.01.2020 • Technical changes and errors excepted.

Use

Offsets

to adjust the readings to be sent.

The unit can calculate a

mixed value

from its own reading and an external value. Set

the mixed value calculation if desired.

Note:

if an external portion is used, all of the following settings (threshold values, etc.)

are related to the overall reading!

The

minimum and maximum readings

can be saved and sent to the bus. Use the

"Reset temperature (and/or humidity) min./max. value" objects to reset the values to
the current readings.

The values are not retained after a reset.

6.4.

Threshold values: Temperature, humidity

Activate the threshold values that you want to use here. The

KNX TH65-AP thermal

hygrometer

provides four threshold values for temperature and two threshold values

for air humidity.

6.4.1. Threshold value 1, 2, 3, 4: Temperature, humidity

The settings options for temperature and threshold values are the same.

Threshold value

Set the threshold values directly in the application program using parameters, or de-
fine them via the bus using a communication object.

Temperature

: Offset in 0.1°C

Humidity

: Offset in % RH

-50…50; 0
-10...10; 0

Use external reading

Yes • No

Ext. Measured value portion of the total
reading

5% • 10% • ... • 50% • ... • 100%

Send internal and total reading

• do not send
• send periodically
• send on change
• send on change and periodically

On change of

(if sent on change)

2% • 5% • 10% • 25% • 50%

Send cycle

(if sent periodically)

5 s • ... • 2 h

Use min. and max. values

Yes • No

Use threshold value 1/2/3/4

Yes • No

«
...
14
15
16
17
18
...
»

Содержание 70184





































Отзывы:

Нет отзывов

Похожие инструкции для 70184

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: IEI Technology Страницы: 85

Бренд: R&S Страницы: 733

Бренд: R&S Страницы: 369

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Seben Страницы: 16

Бренд: Avery Weigh-Tronix Страницы: 54

IMI Sensors Spindler 607A61

Бренд: PCB Piezotronics Страницы: 24

Бренд: ACL Staticide Страницы: 5

Бренд: C.R. Laurence Страницы: 4

Бренд: Neogen Страницы: 9

Бренд: E Instruments Страницы: 2

Бренд: UEi Страницы: 5

Бренд: Anglerfish Creative Lighting Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды