Elsner 70184 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

background image

22

Setting parameters

KNX TH65-AP thermal hygrometer

• Version: 27.01.2020 • Technical changes and errors excepted.

Now specify what should be sent when the control is blocked.
On release, the control variable follows the rule again.

PI control with predetermined application:

This setting provides fixed parameters for a cooling ceiling

Now specify what should be sent when the control is blocked.
On release, the control variable follows the rule again.

2-point-control (only level 2):

2-point-control is used for systems which are only set to ON or OFF.

Enter the hysteresis that prevents frequent on/off switching of temperatures in the
threshold range.

If separate control variables are used, select whether the control variable of the 2nd
level is a 1 bit object (on/off) or an 8 bit object (on with percentage/off).

When blocked, the control variable shall

• not be sent
• send a specific value

Value (in %)

(if a value is sent)

0...100

Control type

•

PI control

Setting of the controller by

• Controller parameter
•

specified applications

Application

• Cooling ceiling

Maximum control variable is reached
at setpoint/actual difference of (in °C)

Cooling ceiling: 5

Reset time (in min.)

Cooling ceiling: 30

When blocked, the control variable shall

• not be sent
• send a specific value

Value (in %)

(if a value is sent)

0...100

Control type

is determined at a higher level for common
variables

•

2-point-control

Hysteresis (in 0.1°C)

0...100; 20

Control variable is a

• 1 bit object
• 8 bit object

Value (in %)

(for 8 bit object)

0...100

«
...
22
23
24
25
26
...
»

Содержание 70184





































Отзывы:

Нет отзывов

Похожие инструкции для 70184

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

Бренд: Yamaha Страницы: 48

Бренд: Cecomp Страницы: 4

Бренд: RADWAG Страницы: 176

WM14-96 - PROGRAMMING

Бренд: CARLO GAVAZZI Страницы: 6

Бренд: Magtrol Страницы: 76

Бренд: Flexim Страницы: 160

Бренд: Neriox Страницы: 10

Бренд: Apogee Страницы: 18

SensoDirect Con200

Бренд: Lovibond Страницы: 24

Бренд: AEMC Страницы: 16

Бренд: Solight Страницы: 2

Бренд: YoloLIV Страницы: 18

RADIATION ALERT Sentry

Бренд: S.E. International Страницы: 8

Бренд: RX Страницы: 8

Everywhereyoulook Frontline X500

Бренд: Teledyne Lecroy Страницы: 8

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды