background image

3

Description

Radio actuator KNX RF-MSG-DST

 • Version:27.06.2018 • Technical changes and errors excepted.

1.

Description

The 

KNX RF-MSG-DST 

is a radio actuator for KNX radio (KNX RF). The actuator con-

trols one drive (blind, shutter, awning or window). Via an additional connector, another
motor control unit is supplied with power (loop-through function). 

The 

KNX RF-MSG-DST

 uses the KNX RF S standard.

Functions:

1 connection for 230 V-drive (STAK3)

1 output 230 V AC (STAK3) for supply of further motor control units

Reception of the control signal via radio KNX RF 

Retransmitter function

 (from version 1.1): Forwarding of all received KNX 

RF telegrams. These can be received by KNX RF participants with the same 
domain address. This allows the range of the KNX RF signal to be increased

Automatic runtime measurement

 of the drives for positioning (incl. fault 

reporting object)

Position feedback

 (movement position, also slat position for shutters)

Position storage

 (movement position) via 1-bit object (storage and call-up 

e.g. via buttons)

Scene control 

for movement position with 16 scenes per drive (also slat 

position for shutters)

Blocking objects and alarm reports

 have different priorities, so safety 

functions always take precedence (e.g. wind block)

Manual or automatic priority setting via time or communication object

Brief time limit

 (movement command blocked) and 

2 movement limits

Configuration is made using the KNX software ETS 5. The 

product file

 can be down-

loaded from the ETS online catalogue and the Elsner Elektronik website on 

www.els-

ner-elektronik.de

 in the “Service” menu.

1.0.1. Scope of delivery

Actuator

Magnet for teaching procedure (telescopic rod)

Rubber seal

Available accessories:

Mains connection wire (5 m)

Connection wire (available in 1 m; 2,5 m; 5 m)

1.1. Technical Data

Housing

Plastic

Protection category

IP 54*

Dimensions

approx. 149 x 72 x 29 (W x H x D, mm)

Weight

approx. 168 g

Ambient temperature

Operation -25…+70 °C, storage -30…+85°C

Содержание KNX RF-MSG-DST



























Отзывы: