elsner elektronik KNX B8-TH Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

background image

34

Parameter settings

Interface KNX B8-TH

• Version: 24.08.2016 • Technical changes and errors excepted.

The

minimum and maximum readings

can be saved and sent to the bus. Using the

"Reset reading min/max." objects the values can be reset to the current readings.

The values are not retained after a reset.

5.7.

Humidity threshold values

The settings for the "humidity threshold values" and other air humidity settings are
only shown if the circuit board sensor input has been set to "temperature and humidity
sensor" in the "General settings".

The

Interface KNX B8-TH

provides two threshold values for the humidity measure-

ment of the sensors connected to the device.

5.7.1. Threshold value 1/2

Threshold value

Set, in which cases

threshold values and delay times

received via objects are to be

retained. The parameter is only taken into consideration if the setting via object is ac-
tivated below. Please note that the setting "After power supply restoration and pro-
gramming" should not be used for the initial start-up, as the factory settings are always
used until the first communication (setting via objects is ignored).

Set the threshold value directly in the application program using parameters, or define
them via the bus using a communication object.

Threshold value setting using parameter:

Set the threshold values and hysteresis directly.

Threshold value setting using a communication object:

Define, how the threshold value is to be received from the bus. Basically, a new value
can be received, or simply a command to increase or decrease.

During initial commissioning, a threshold value must be defined, which will be valid
until the first communication with a new threshold value. For units which have already

Use minimum and maximum value

No • Yes

Use threshold value 1/2

No • Yes

Maintain the

threshold values and delays received via
communication objects

• never
• after power supply restoration
• after power supply restoration and
programming

Threshold value setting using

Parameter

• Communication objects

Threshold value in 0.1% RH

1 … 1000; 650

«
...
33
34
35
36
37
...
»

Содержание KNX B8-TH

























































Отзывы:

Нет отзывов

Похожие инструкции для KNX B8-TH

Бренд: UFESA Страницы: 27

Бренд: Oki Страницы: 3

Бренд: Manfrotto Страницы: 2

Бренд: RACLET Страницы: 48

Бренд: RACLET Страницы: 31

Бренд: Racelogic Страницы: 2

Бренд: Xblitz Страницы: 16

Бренд: Obelink Страницы: 2

Бренд: TecnoVideo Страницы: 4

Бренд: UniFi Страницы: 15

990E0-54P56-000

Бренд: Suzuki Страницы: 12

Бренд: CYBEX Страницы: 24

Бренд: Uni-Com Страницы: 6

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: SI-Elektronik Страницы: 16

Бренд: FLAMMA Страницы: 32

Бренд: BEGA Страницы: 3

Бренд: iGPSPORT Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды