elsner elektronik KNX B8-TH Скачать руководство пользователя страница 51

Страница: 51 / 56

Parameter settings

Interface KNX B8-TH

• Version: 24.08.2016 • Technical changes and errors excepted.

Input as switch:

If a button with switch function is assigned to the input, select the bus function
"Switch" and specify which value is sent when pressing/releasing the button and when
it will be sent.

Input as changeover switch:

Select the "Changeover switch" bus function if a button with changeover function is as-
signed to the input.

Then decide whether an additional function is to be used if the button is held down.

no additional function

is used for button held down, decide whether the change-

over command is sent when pressing or when releasing the button.

If you are using the

additional function for button held down

, set the period be-

tween button tapped and button held down and what is to take place when the button
is pressed and released at different times.

Function

Switch

Command when pressing the button

• send 0
• send 1
• do not send telegram

Command when releasing the button

• send 0
• send 1
• do not send telegram

Send value

• no change
• for change to 1
• for change to 0
• for change and cyclical
• for change to 1 and cyclical
• for change to 0 and cyclical

Cycle

(if sent cyclical)

5 s • 10 s • 30 s • 1 min • 2 min • 5 min • 10
min • 20 min • 30 min • 1 h • 2 h

Function

Changeover Switch

Use additional function for button held
down

No • Yes

Use additional function for button held
down

• Yes

Command when pressing the button

• Switching
• Do not send telegram

Command when releasing the button

• Switching
• Do not send telegram

Use additional function for button held
down

No •

Yes

Time between tap and hold (in 0.1 sec)

0...50; 10

Содержание KNX B8-TH

























































Результаты поиска

Содержание KNX B8-TH

Отзывы:

Похожие инструкции для KNX B8-TH

Бренды по названию

Популярные бренды

elsner elektronik KNX B8-TH, Установка и настройка

Результаты поиска

Содержание KNX B8-TH

Отзывы:

Похожие инструкции для KNX B8-TH

Бренды по названию

Популярные бренды