elsner elektronik KNX B8-TH Скачать руководство пользователя страница 37

Страница: 37 / 56

Parameter settings

Interface KNX B8-TH

• Version: 24.08.2016 • Technical changes and errors excepted.

Block

The switching output can be blocked using an object.

Set the

output behaviour during and after blocking.

The behaviour of the switching output on release is dependent on the value of the pa-
rameter "Switching output sends" (see "Switching output")

5.8.

Humidity PI control

The settings for the "humidity PI control" and other air humidity settings are only
shown if the circuit board sensor input has been set to "temperature and humidity sen-
sor" in the "General settings".

If you activate humidity control, you can use the following settings to define control
type, target values, and humidification and dehumidification.

General rules

The

Interface KNX B8-TH

can be used to control one- or two-stage dehumidification

or combined humidification/dehumidification.

Use switching output block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before first communi-
cation

0 • 1

Behaviour of the switching output

On block

• Do not send message
• send 0
• send 1

On release
(with 2 seconds release delay)

[Dependent on the "Switching output
sends" setting]

Switching output sends on change

• Do not send message
• Send switching output status

Switching output sends on change to 1

• Do not send message
• if switching output = 1



send 1

Switching output sends on change to 0

• Do not send message
• if switching output = 0



send 0

Switching output sends on change and
periodically

Send switching output status

Switching output sends on change to 1
and periodically

if switching output = 1



send 1

Switching output sends on change to 0
and periodically

if switching output = 0



send 0

Use humidity control

No • Yes

Содержание KNX B8-TH

























































Результаты поиска

Содержание KNX B8-TH

Отзывы:

Похожие инструкции для KNX B8-TH

Бренды по названию

Популярные бренды

elsner elektronik KNX B8-TH, Установка и настройка

Результаты поиска

Содержание KNX B8-TH

Отзывы:

Похожие инструкции для KNX B8-TH

Бренды по названию

Популярные бренды