ELNA 745 - Скачать руководство пользователя

Страница: 41 / 61

1. Remove: Mains lead - Sewing foot - Needles.

2. Disengage moving cutter.

3. Basic position: Turn dial

"a"

to bring indicator to position mark

"1"

and check if

clearance of

0.2 to 0.3mm

is obtained between fixed blade

"b"

and needle plate edge.

Make sure that there is no play among cutting width cam unit

"d"

, lever

"e"

and shaft

"f"

4. If not, loosen screws

"c"

5. Push dial "

" to the right to obtain a clearance of

0.2 to 0.3mm

6. Fasten screws

"c"

and check the clearance between fixed blade "b" and needle plate edge.

7. Re-engage moving cutter. Turn handwheel towards you and bring moving cutter to its

lowest position. Make sure if the moving cutter release knob

"g"

is not touching the shaft

support

"h"

(the gap between

"g"

and

"h"

is 0.1

0.2mm).

8. Turn cutting width dial

"a"

to the widest position

"7"

and check if the knob

"g"

touches

the shaft support

"h"

. Then, turn cutting width dial to the narrowest position

"1"

and

check if the gap between the knob

"g"

and the shafat support

"h"

is within 0.1

0.2mm.

9. If those gaps are not available, loosen screw

"j"

and get them by turning the shaft support

"h"

forward/backward or right or left.

10.Tighten screw

"j"

POSITION OF FIXED CUTTER AND CUTTING WIDTH DIAL SETTING

17b

Содержание 745 -






























































Результаты поиска

Содержание 745 -

Отзывы:

Похожие инструкции для 745 -

Бренды по названию

Популярные бренды

ELNA 745 -, Руководство по обслуживанию

Результаты поиска

Содержание 745 -

Отзывы:

Похожие инструкции для 745 -

Бренды по названию

Популярные бренды