background image

             

 

 

 

                    OPERATING & MAINTENANCE   

INTRODUCTION                                            INSTRUCTIONS

READ THIS BOOK

Self-Contained Carpet Extractor

ACHIEVER 80

ACHIEVER 110

This operator’s book has important information for the use 

and safe operation of this machine.  Read this book care-

fully before starting the machine.  Keep this book and tell 

all operators to read the book.  If you do not follow the 

instructions, you can cause an injury or damage equipment, 

furniture or buildings.

For  additional  information  refer  to  the Triple  S  website 

www.triple-s.com or write to: 

               

Triple S

 

              2 Executive Park Drive

              Billerica, MA  01862

Carefully inspect all components to ensure that there is no 

concealed freight damage.  If such damage is discovered, 

file a “CONCEALED DAMAGE REPORT” immediately 

with the delivering carrier. 

The contents of this manual are based on the latest product 

information available at the time of publication.  Triple S  

reserves the right to make changes or improvements to its 

machines without notice.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOR YOUR CONVENIENCE, RECORD THIS

IMPORTANT INFORMATION:

 

MODEL

_______________________________

 

SERIAL NUMBER

______________________

 

PART NUMBER

 ________________________

 

DATE PURCHASED

 ____________________

Содержание ACHIEVER 110













Отзывы: