96
MP500/4N-8-16 Installation
To acquire a KP500DP/N or KP500D/ST touch screen keypad, it is sufficient to press the
F4
key when the following message appears
on the display.
Figure 64 - Message of KP500DP/N - KP500D/ST keypad acquisition
6.2.2 Procedure for acquiring bus devices
IMPORTANT!
The instructions below assume that the devices have not yet been acquired.
Otherwise, see Chapter 7
– Maintenance.
To acquire the various devices on the system bus, follow the instructions below:
1. Select the keypad to be used to acquire system devices from among the keypads present in the system. It is also possible to use
the service keypad (see paragraph
2. Press the programming button (PROG) on the keypad display (if there is a KP500DP/N or KP500D/ST keypad, press
F4
). The
control panel registers it by assigning the “KP01” address. If it is a service keypad, it will be assigned the address “KP08”.
3. The «MAINTENANCE» / «LINGUA-LANGUAGE» menu will appear on the keypad display.
If the language is to be changed, press the
OK
button, otherwise press the ▼ key until «MAINTENANCE» / «ACQUIRE» appears,
press
OK
again and go on to point 7.
4. «LINGUA-LANGUAGE» / «KP01:KP 01» appears on the display (second line). KP01 is the first keypad of the system, or the one
that was just acquired. If the service keypad is being used, the message «KP08:KP 08» will appear. Press the
OK
button.
5. «ITALIANO» will appear on th
e display. Use the ▼▲ keys to select the language desired and confirm the selection by pressing the
OK
key.
6. «Download in progress >>>>...» will appear on the display. When the download of the new language is complete, the message
«DOWNLOAD OK» will appear. Press
OK
and then
ESC
.
IMPORTANT!
During the download, the power supply must absolutely not be disconnected from the keypad!
7.
“ACQUISITION IN PROGRESS...” will appear on the display and the control panel is ready to acquire other devices.
8. Proceed with the acquisition of the other devices by pressing the programming button of each of them.
The yellow LED located next to the button of the device will turn off as soon as it is acquired.
Each time a new device is acquired, the keypad emits 3 beeps and the device type will appear on the display (KP = keypad;
EP = expansion; DK = reader; ER = radio expansion; AS = POWER/S.) with the address assigned to it.
Once the acquisition of all the devices is complete, press
ESC
to exit from the menu.
Now it is possible to proceed with the system configuration as illustrated in the Programming Manual.
IMPORTANT!
The addresses are assigned progressively and according to family of belonging; it is not necessary to follow a
pre-established order. If the operator wants the device addresses to follow certain logic, they must be acquired in that order.
Example:
In a system with two keypads, one expansion, two readers, and a radio expansion, there will be the following combination:
KP01
KP02
EP01
DK01
DK02
ER01
AS01
Suggestion:
Take note of the address of each individual device on the labels provided with the control panel.
6.3
USING THE SERVICE KEYPAD
For the system acquisition and programming operations, it is possible to use a keypad connected directly to the SERVICE connector of
the control panel via the specific cable. For more details, see paragraph
5.12.7 Connecting the cable for KP SERVICE keypad
The service keypad must be acquired according to the method described above. The system automatically assigns it the address n. 08.
At the end of the operation, it is possible to disconnect this keypad without generating tamper and therefore without having to delete it.
When inserted again, it does not require another acquisition and the keypad will be immediately operative.
IMPORTANT!
Using the service keypad precludes the possibility of having 8 keypads on the system (as address 8 is already
occupied, it will be possible to connect a maximum of 7 keypads).
