manualshive.com logo in svg

Electrolux Side by Side Refrigerators, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Side by Side Refrigerators Скачать руководство пользователя страница 70

69

MODELS WITH ELECTRONIC CONTROL

To gain access to dispenser area:

1.

Snap light socket loose.

2.

Remove six screws from power board. (See Figure 13.)

3.

Pull board straight out of housing.

4.

Disconnect plug on left side of board.

5.

Disconnect four wires to dispenser actuator
switches. (See Figure 14.)

6.

With the board detached, remove three screws from
dispenser housing and pull housing forward. (See
Figure 15.)

Remove
screws

Pull housing
forward

Figure 15

7.

Remove water line from dispenser housing by
pulling straight out. (See Figure 16.)

Remove
water line

Figure 16

With the water line removed, the upper part of the
dispenser is free of the freezer door panel.The main
housing is built into the door panel and is not removable.
(See Figure 17.)

Figure 17

Main housing
for dispenser
is part of outer
door panel.

The ice door, actuator switches, and return springs can
be serviced with control module removed. (See Figure
18.)

Figure 18

Ice Door

Door Closer

Return Springs

Actuator
Switches

Figure 14

Unplug
board

Disconnect actuator
switches

The door closer is mounted on the side of the housing
(see Figure 19) and is connected to the door arm with a
gear wheel to slow the closing of the door (see Figure
20), and allow enough time for the ice to clear the chute.
The door takes approximately 20 seconds to close after
the glass is removed from the actuator.

Ice Door
Closer

Figure 19

Figure 13

Remove
screws

Unsnap
light
socket

Содержание Side by Side Refrigerators





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды