Electrolux Side by Side Refrigerators Скачать руководство пользователя страница 52

Страница: 52 / 100

To Replace Ice Maker Control Arm Shut-OFF Switch

Remove front Cover.

Remove three screws that attach Mounting Plate
to Support Housing.

Disconnect three Ice Maker Control Arm Shut-Off
Switch wire leads.

Raise Ice Maker Control Arm Lever.

Remove two Ice Maker Control Arm Shut-Off
Switch mounting screws.

Remove switch.

Replace switch in reverse order.

To Replace Ice Maker Thermostat

Remove front Cover.

Remove three screws that attach Mounting Plate to
Support Housing.

Loosen two Thermostat retaining clip mounting
screws.

Disconnect two thermostat wire leads and remove
thermostat.

Apply thermal mastic sealer to sensing surface of
replacement thermostat to ensure a positive bond
to mold.

Replace thermostat in reverse order.

To Replace Hold Switch

1. Remove front Cover.
2. Remove three screws that attach Mounting Plate to

Support Housing.

3. Disconnect six Hold Switch wire leads.
4. Remove two Hold Switch mounting screws.
5. Remove Hold Switch.
6. Replace in reverse order.

Figure F6

Screw

Motor

Screw

Support

Ice Maker
Control Arm

Cam

Clamp

Screw

I.D. Plate

Thermal
Cutoff
Assembly

Screw

Thermostat
Assembly

Screw

Hold Switch
SPDT

Shut-Off Switch
SPDT

Ice Maker
Arm Spring

Water Fill
Switch
SPDT

Insulator

Valve Switch
Plate

Cover

Gear

Screw

Mounting
Plate

Spring

Spacer

Lever Arm

Screw

Wiring Harness
Connector Plug

To Replace Thermal Cut-Out (TCO)

1. Remove front Cover.
2. Remove three screws that attach Mounting Plate

to Support Housing.

3. Pull cable assembly free from support housing. It will

slide out easily.

4. Loosen screw securing clamp to TCO. TCO should

come free after tension from clamp is released.

5. Disconnect TCO from two wire nuts. One end is

connect to cable assembly and other end is
connected to motor and mold heater.

6. Install new TCO.
7 Reassemble in reverse order.

Содержание Side by Side Refrigerators





































































































Результаты поиска

Содержание Side by Side Refrigerators

Отзывы:

Бренды по названию

Популярные бренды

Electrolux Side by Side Refrigerators, Руководство по обслуживанию

Результаты поиска

Содержание Side by Side Refrigerators

Отзывы:

Бренды по названию

Популярные бренды