manualshive.com logo in svg

Electrolux Side by Side Refrigerators, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Side by Side Refrigerators Скачать руководство пользователя страница 3

2

System Diagnostics ............................................................................................................................... 24

System Exploded View Diagram ..................................................................................................... 25

Controls Exploded View Diagram (Rear Filter) ................................................................................... 26

Controls Exploded View Diagram (Front Filter) .................................................................................. 27

SECTION D - AIR CIRCULATION

Principles of Automatic Defrost Operation .............................................................................................. 28

Air Circulation Patterns ......................................................................................................................... 28

SECTION E - REFRIGERATION SYSTEM

Definitions ........................................................................................................................................... 29

Recovery ...................................................................................................................................... 29

Recycling ...................................................................................................................................... 29

Reclaim ........................................................................................................................................ 29

Safety Warnings .................................................................................................................................. 29

Compressor Testing ....................................................................................................................... 29

Charging Sealed Systems .............................................................................................................. 29

Soldering ............................................................................................................................................. 30

Basic Components ............................................................................................................................... 30

Perimeter Hot Tube .............................................................................................................................. 30

Refrigerant Cycle ................................................................................................................................. 30

Low or High Side Leak or Undercharge ................................................................................................... 30

Testing for Refrigerant Leaks ................................................................................................................ 31

Checking for Internal (Hot Tube) Leaks .................................................................................................. 31

Compressor Replacement ..................................................................................................................... 31

To Flush The System ..................................................................................................................... 31

To Use Dry Nitrogen To Flush The System ...................................................................................... 32

To Use Refrigerant To Flush The System ........................................................................................ 32

Installing a New Compressor ................................................................................................................. 32

Evaporator Replacement ...................................................................................................................... 33

Heat Exchanger Replacement ............................................................................................................... 35

Perimeter Hot Tube Repair Kit ............................................................................................................... 36

Condenser Replacement ....................................................................................................................... 38

Filter-Drier Installation .......................................................................................................................... 38

Evacuating & Recharging ..................................................................................................................... 38

Equipment Needed for Evacuation & Recharging .............................................................................. 39

Installing Evacuation & Recharging Equipment ................................................................................. 39

Evacuating System ........................................................................................................................ 39

Charging The System ..................................................................................................................... 39

Final Leak Test.................................................................................................................................... 40

R-134a Service Information ................................................................................................................... 41

Verify Refrigerant Type In The System ............................................................................................ 41

      Dedicated Equipment ............................................................................................................... 41

R-134a Refrigeration Systems ......................................................................................................... 41

Miscibility of R-134a and Ester Oil ................................................................................................... 41

Water in Refrigeration System ......................................................................................................... 42

Vacuum Pump Maintenance ........................................................................................................... 42

Refrigerant Leaks ........................................................................................................................... 43

Leak Detection .............................................................................................................................. 43

R-134a Properties .......................................................................................................................... 43

HFC-134a, CFC-12 Pressure Temperature Chart............................................................................... 44

R-134a Health & Safety Information ....................................................................................................... 45

Inhalation Toxicity .......................................................................................................................... 45

Cardiac Sensitization ..................................................................................................................... 45

Spills or Leaks ............................................................................................................................... 45

Skin and Eye Contact .................................................................................................................... 45

Содержание Side by Side Refrigerators





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды