Electrolux 603877, Инструкция по установке и эксплуатации

Страница: 16 / 46

16
D.7 Residual risks
The machine has several risks that were not completely
eliminated from a design standpoint or with the installation of
adequate protection devices. Nevertheless, through this
manual the Manufacturer has taken steps to inform operators
of such risks, carefully indicating the personal protection
equipment to be used by them. In order to reduce the risks,
provide for sufficient spaces while installing the unit. To
preserve these conditions, the areas around the machine
must always be:
• kept free of obstacles (e.g. ladders, tools, containers, boxes,
etc.);
• clean and dry;
• well lit.
For the Customer's complete information, the residual risks
remaining on the machine are indicated below: such situations
are deemed improper and therefore strictly forbidden.
Residual risk Description of hazardous
situation
Slipping or falling The operator can slip due to water
or dirt on the floor
Slipping or falling The operator can slip due to water,
beer or dirt on the floor.
Catching, dragging or
crushing Catching or dragging of the oper-
ator or other persons in the drive,
during the machine work phase,
due to improper actions, such as:
• placing an arm inside the
machine to remove a stuck rack
without stopping the machine
by operating an emergency
switch;
• accessing the rack handling
system without stopping the
machine by operating an emer-
gency switch.
Use of improper clothing with
loose parts (e.g. necklaces,
scarves, shawls, ties, etc.) or long
hair not gathered, which could get
caught up in moving parts.
Burns/abrasions (e.g.
heating elements,
cold pan, cooling cir-
cuit plates and pipes) The operator deliberately or unin-
tentionally touches some
components inside the machine
without using protective gloves.
Stab wounds The operator deliberately or unin-
tentionally touches some
components with sharp edges
during the machine cleaning with-
out using protective gloves.
Burns The operator deliberately or unin-
tentionally touches some
components inside the machine or
dishes at the outfeed without using
gloves or without allowing them to
cool.
Shearing of upper
limbs
The operator violently closes the
front panels.
Residual risk Description of hazardous
situation
Electrocution Contact with live parts during
maintenance operations carried
out with the electrical panel
powered
Breakage or bursting
of cap/cylinder Accidental knocking of the cap on
the cylinder and/or dropping of the
cap when changing the keg (possi-
ble cracking of the material)
Lack of required maintenance as
provided for in the relevant sec-
tions. Parts subject to wear not
checked and/or replaced.
Falling from above The operator intervenes on the
machine using unsuitable systems
to access the upper part (e.g. rung
ladders, or climbs on it)
Crushing or injury The specialised personnel may
not correctly fix the control panel
when accessing the technical
compartment. The panel could
close suddenly.
Crushing or injury During lifting of the cylinder, the
operator's hand could get
squashed between the cylinder
and the top of the cabinet. There-
fore do not place a hand on the
cylinder during this stage.
Crushing or shearing Possible risk of injury to upper
limbs during the hood closing
operation.
Crushing or shearing Possible risk of injury to upper
limbs during the closing operation
of the lid on the rear of the
appliance.
Tipping of loads When handling the machine or the
packing containing it, using unsuit-
able lifting systems or accessories
or with the unbalanced load
Chemical (refrigerant
gas) Inhalation of refrigerant gas.
Therefore always refer to the appli-
ance labels
Chemical Contact with chemical substances
(e.g. detergent, rinse aid, scale
remover, etc.) without taking
adequate safety precautions.
Therefore always refer to the
safety cards and labels on the
products used.
IMPORTANT
In case of a significant anomaly (e.g. short circuits,
wires coming out of the terminal block, motor
breakdowns, worn electrical cable sheathing, etc.)
the operator must immediately deactivate the
machine.
E TECHNICAL DATA TABLE
E.1 Main technical characteristics
IMPORTANT
For overall dimension please refer to the “Installation Diagram“.
For all electric data, please refer to “C.4
Machine and manufacturer's identification data “