Electrohome VistaGRAPHX 2500 Скачать руководство пользователя страница 69

Страница: 69 / 101

MAINTENANCE

VistaGRAPHX 2500 User's Manual

4-11

The display appears compressed or stretched
1. The frequency of the pixel sampling clock is incorrect for the current source.

Adjust pixel tracking up or down.

Display quality appears to drift from good to bad, bad to good...
1. The operating temperature of the projector may not be constant. Watch that

the projector is not located too close to heating/air conditioning vents.

2. The source input signal may be of low quality.

3. The horizontal or vertical frequency of the input may have changed at the

source end.

The display has suddenly frozen, or an unknown menu has appeared
1. You may have accidentally entered a special engineering code using the

key with certain numbers. Press

to cancel the function and return to

presentation level.

2. If the screen blacks out, it is possible that excessive voltage noise on the AC

or ground input has interrupted the projector’s ability to lock on to a signal.
Turn the projector off, wait for the lamp fans to stop and unplug. Plug in
again and power up as usual.

The display is not sharp or "clean"...
1. Display adjustment may be required. Rotate the focus knob to adjust for best

focus, then adjust brightness, contrast and detail.

2. Is a BNC T-connector being used? Use a distribution amplifier to boost

signal levels.

3. Is the video input signal properly terminated? Set in Preferences menu.

4. The screen size may be too large. As screen size increases, magnification

increases, reducing brightness.

5. The source input signal may be of low quality.

Colors in the display are inaccurate...
1. The color, tint and/or color temperature settings may require adjustment

from within the Image Settings menu.

The display is not rectangular...
1. Is the vertical offset adjusted correctly for the current throw distance? Use

the vertical offset knob on the front of the projector and see 2.8, Zoom,
Focus and Vertical Offset for minor adjustments.

2. Is the projector lens surface parallel to the screen? See 2.7, Leveling.

The display is "noisy"...
1. Display adjustment may be required. Adjust pixel tracking and phase.

2. The video input may not be terminated. Make sure the video input is

terminated (75

). If it is the last connection in a loop-through chain, the

video input should be terminated at the last projector only.

3. The signal cables carrying the input signal may be of poor quality. Use only

good quality signal cables. Electrohome cables are recommended.

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Содержание VistaGRAPHX 2500






































































































Результаты поиска

Содержание VistaGRAPHX 2500

Отзывы:

Похожие инструкции для VistaGRAPHX 2500

Бренды по названию

Популярные бренды

Electrohome VistaGRAPHX 2500, Руководство пользователя

Результаты поиска

Содержание VistaGRAPHX 2500

Отзывы:

Похожие инструкции для VistaGRAPHX 2500

Бренды по названию

Популярные бренды