Electrohome VistaGRAPHX 2500 Скачать руководство пользователя | Manualshive

Страница: 4 / 101

background image

Section 2

Installation & Setup

VistaGRAPHX 2500 User's Manual

2-1

This section explains how to install and set up the projector. If you are familiar with the projector and want to
quickly set it up for temporary use, follow the Quick Setup instructions. For a complete setup, follow the
instructions and guides covered in the remaining subsections.

NOTES: 1) The lens for the projector is not mounted when shipped from the factory. For instructions on how to
install or replace a lens, refer to 4.5, Replacing the Lens. 2) This manual assumes the video decoder is installed.

Follow these 6 steps for quick setup of the projector.

Position the Projector
Set the projector at the proper throw distance (projector-to-screen distance) and
vertical position. See 2.3, Projector Position and Mounting. Make sure that the
projector is level from side-to-side (see 2.7, Leveling).

Connect a Source
Locate the input panels at the rear of the projector. The upper right panel accepts
an RGB input (via BNC connectors). The lower left panel accepts a composite
video and S-video input. Connect a source to the appropriate panel.

Connect the Line Cord
Plug the special notched AC line cord (power cord) into the AC power socket at
the left rear of the projector. This cord is rated at 15 amps rather than the 8-10
amps in other typical cords. Input power required is 100 VAC to 240 VAC, 50 to
60 Hz @ 11 amps.

WARNING:

Use only the special notched AC line cord. Do not

attempt operation if the AC supply is not within the

specified voltage and power range.

Turn the Projector ON
Using either the built-in or IR remote keypad, press

and hold for a second

to turn the projector on. The VistaGRAPHX 2500 logo will be displayed after a
brief delay. Let the projector warm up for five minutes.

Select a Source
Using either the built-in or IR remote keypad, press

,

, or

to

select and display the image for the source you have connected in Step 2. By
default, it will resize as needed — the image will be as large as possible while
maintaining its original aspect ratio.

2.1

Quick Setup

STEP 1

'

STEP 2

'

STEP 3

'

STEP 4

'

STEP 5

'

«
...
2
3
4
5
6
...
»

Содержание VistaGRAPHX 2500






































































































Отзывы:

Нет отзывов

Похожие инструкции для VistaGRAPHX 2500

Бренд: RocketFish Страницы: 2

Бренд: NEC Страницы: 2

Бренд: RVsecure Страницы: 5

Бренд: Laserworld Страницы: 12

Gobo Projector 1

Бренд: Rush Страницы: 24

Бренд: Minolta Страницы: 42

Paramount PC930 Series

Бренд: PEERLESS Страницы: 3

Бренд: Vutec Страницы: 11

CineVERSUM 110 R9010120

Бренд: Barco Страницы: 135

Бренд: Panasonic Страницы: 111

Бренд: Panasonic Страницы: 112

Бренд: Panasonic Страницы: 150

Бренд: Panasonic Страницы: 212

Бренд: Panasonic Страницы: 213

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 24

CP-SX1350 Series

Бренд: Hitachi Страницы: 16

CP-SX1350 Series

Бренд: Hitachi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды