ELECTRO FREEZE SOFT SERVE TWIST SL500 Скачать руководство пользователя | Manualshive

Страница: 23 / 77

background image

14

184599

ELECTRO FREEZE Soft Serve Model SL500

3

2

6

1

5

CAUTION

To avoid electrical shock
or contact with moving
parts, make sure all
switches are in the “OFF”
position and that the main
power supply is
disconnected. Some
freezers have more than
one disconnect switch.

It is important that the freezer be disas-
sembled, washed, lubricated and sani-
tized before operation.

6

Disassembly and Cleaning

The cleaning and sanitizing instructions
explained in this manual are required to
maintain a clean, sanitary freezer. The
freezer should be disassembled,
cleaned, reassembled, lubricated and
sanitized daily to ensure the best pos-
sible product quality and freezer opera-
tion.

Persons assembling, cleaning, or sani-
tizing the freezer must wash and sanitize
hands and forearms with an approved
sanitizer.

6.1

Cleaning Accessories

The following accessories shipped with the freezer are necessary for cleaning,
sanitizing and disassembly/assembly.

1

HC150009 BRUSH.
HC158012 HANDLE.

4-inch diameter with 36-inch

handle, used for cleaning the
cylinder.

2

HC158077 BRUSH.

9/16 inch with 36 inch handle, used

for cleaning the drain tube.

3

HC158003 BRUSH.

Double end, 1-1/8 inch diameter and

7/16 inch diameter, used for clean-
ing the mix inlet tube, mix feed
tube, head and general cleaning.

4

HC196103 BOTTLE - WASH 500ml

500ml squeeze bottle used to

clean out small openings.

5

HC169374 TOOL - O-RING

REMOVAL.

Aids in removing O-rings from

plungers, dispense head, and mix
feed tube.

6

HC158000A LUBRICANT -

PETROL GEL

Approved lubricant for moving

parts and O-rings. See assembly
instructions for lubricating points.

7

HC115536 KIT - O-RING.

(NOT SHOWN)

This kit contains all O-rings and

seal needing replacement on a
regular basis.

Figure 6-1 Accessories

HC158009 BRUSH-4” DIA W/O HANDLE

HC158012 HANDLE-BRUSH FIBERGLASS

HC158077 BRUSH-9/16 DIA X 36” HANDLE

HC158003 BRUSH-7/16 & 1-1/8” DOUBLE END

HC158000A
LUBRICANT-PETROL GEL 4 OZ TUBE

HC169374
TOOL-O RING REMOVAL

4

HC196103 BOTTLE - WASH 500ml

«
...
21
22
23
24
25
...
»

Содержание SOFT SERVE TWIST SL500














































































Отзывы:

Нет отзывов

Похожие инструкции для SOFT SERVE TWIST SL500

Бренд: GE Страницы: 16

Бренд: GE Страницы: 16

Бренд: Traulsen Страницы: 4

Бренд: HOMCOM Страницы: 25

Бренд: Yeti Страницы: 12

Бренд: Thermador Страницы: 94

Бренд: IKEA Страницы: 52

Бренд: True Страницы: 13

Бренд: JUNO Страницы: 40

Бренд: Avanti Страницы: 32

Бренд: V-ZUG Страницы: 48

Бренд: AEG Страницы: 20

Бренд: Smeg Страницы: 20

Бренд: Russell Hobbs Страницы: 24

Бренд: Dometic Страницы: 36

Бренд: KRAFT Страницы: 56

ACTIVESMART RS36A80

Бренд: Fisher & Paykel Страницы: 88

Бренд: Boss Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды