ELECRAFT K3 Скачать руководство пользователя страница 24

Страница: 24 / 78

Filter Presets (I/II)

Each

ope

mode

ovi

des

‘

ng’

prese ts

and

, which store filter settings on a

per-VFO, per-mode basis (excluding FM). They are
updated continuously as you change filter settings.
(Fixed, per-

mode

‘

nor

mal

’

ngs

available; see below.)

You can alternate between the

and

settings by

holding

I/ II

Thi

when

you’

using wide and narrow settings during contest or
DX operation.

The

and

settings for VFOs A and B are

independent.

Filter Normalization (NORM)

Standard Settings

To get quickly to a standard per-mode bandwidth
and reset any passband shift or cut, hold

N OR M

(normalize). The normalized bandwidth is 400 Hz
in CW and DAT A modes, 2.7 or 2.8 kHz in SSB
modes, and 6 kHz for AM.

Whenever you normalize the filter passband,

two small "wings" appear at the left and right ends
of the DSP filter passband graphic as shown below.

Moving any DSP control makes the "wings"
disappear, as a reminder that the passband is no
longer normalized.

Custom Settings (NO RM1 and NORM2)

In addition to the K3's standard "NORM" values,
you can save two of your own setups in each mode,
then recall them using the

N OR M

function. These

setups are referred to as NORM1 and NORM2.

To save a custom normalization setting:



set up the filter passband as desired for the
current mode



hold

N OR M

until you see

S AV

seconds)



rotate the knob slightly left or right to save it as

NO RM 1

NO RM 2

The arrows to the left and right of

S AV

are a

reminder that you can rotate the knob to get to the
two user-defined normalization settings.)

To recall, hold

N OR M

until you see

NO R

(about 1/2 second), then rotate the knob left or right
to recall

NO RM 1

NO RM2

Narrow DSP Filter Types

For

bandwi

ngs

100

ower

K3’

DSP normally uses a type of filter that minimizes
ringing: the

inite

mpulse

esponse or FIR filter.

you’

per

don’

small amount of ringing, you can select

nfinite

mpulse

pons

e”

hes

bandwidths. Locate

CONFIG:FLx BW

menu entry,

then tap

until you see

I I R O N

. Both main and

sub receivers will use the same setting.

Содержание K3














































































Результаты поиска

Содержание K3

Отзывы:

Похожие инструкции для K3

Бренды по названию

Популярные бренды

ELECRAFT K3, Руководство пользователя

Результаты поиска

Содержание K3

Отзывы:

Похожие инструкции для K3

Бренды по названию

Популярные бренды