ELECRAFT K3 Скачать руководство пользователя страница 18

Страница: 18 / 78

KIO3 Module

The KIO3 provides serial I/O, control signals, audio
in/out for use with sound cards, speaker outputs,
and auxiliary headphone and mic jacks.

RS232

The RS232 port can operate at up to 38,400 baud. A
straight-through cable is required.

you’

bui

lding your own cable, you can use as

few as three wires (RXD, T XD, and ground; see
table below). DT R and RT S are optional.

This table use s EIA standard descriptions,

which are from the pe rspe ctive of the PC . These
diffe r from K2 documentation, e ven though the
connections are functionally identical.

Pin #

Description

1,6,8,9

Not used

RXD IN (data

from

K3)

T XD OUT (data

from

PC)

DT R (see

PTT and Ke ying

, below)

Ground (RF isolated)

RT S (see

PTT and Ke ying

, below)

RS232 C onne ctor (female , on KIO3 panel)

Se rial Port Setup:

Set

CONFIG:RS232

for the

desired baud rate. Software should be set up at the
same rate; 8 data bits, no parity, 1 stop bit.

DTR and RTS:

These are

not

used as serial I/O

handshaking lines. Instead, the K3 can use these as
PTT IN or KEY IN (see

CONFIG:PTT-KEY

). The

default for both signals is

inactive

. Refer to

application software documentation to determine if
it can use RS232 signal lines for PTT or keying.

If a PC or othe r de vice asse rts RTS or DTR

while

you’

PTT-KEY

menu entry, the K3

will enter TEST mode as a pre caution.

ACC (Accessory I/O)

ACC connector pinouts are listed below.

ACC is not a VGA vide o conne ctor. The K3

doe s not provide video output.

Pin #

Description

FSK IN (see

FSK Input

)

AUXBUS IN/OUT (see KRC2 or XV-
Series transverter instruction manual)

BAND1 OUT (see

Band Outputs

)

PTT IN (in parallel with MIC PTT)

Ground (RF isolated)

DIGOUT 0 (see

Transve rte r C ontrol

)

K3 ON signal (out) or T X INH (in)
(see

Transve rter Control

TX INH

)

POWER ON (see pg. 43)

BAND2 OUT (see

Band Outputs

)

KEYOUT -LP (10 mA keying output)

DIGOUT 1 (see

DIGOUT1

)

Ground (RF isolated)

BAND0 OUT (see

Band Outputs

)

BAND3 OUT (see

Band Outputs

)

EXT ALC input (see

Exte rnal ALC

pg. 27)

ACC Conne ctor (female, on KIO3 panel)

FSK Input (for FSK D Data Mode)

This is a TTL input pulled up to 5V, compatible
with TTL-level PC outputs. When used with an
RS232 output signal from the PC, a level translator
is required (refer to your software manual).

DIGO UT 1

DIGOUT 1 is a per-band/per-antenna open-drain
output for controlling antenna switches, preamps,
filters, etc. See

CONFIG:DIGOUT1

Содержание K3














































































Результаты поиска

Содержание K3

Отзывы:

Похожие инструкции для K3

Бренды по названию

Популярные бренды

ELECRAFT K3, Руководство пользователя

Результаты поиска

Содержание K3

Отзывы:

Похожие инструкции для K3

Бренды по названию

Популярные бренды