ELCOM Uniq 150, Руководство по обслуживанию

Страница: 27 / 41

46
Elcom, spoločnosť s ručením obmedzeným, Prešov Elcom, spoločnosť s ručením obmedzeným, Prešov
47
Uniq 150 Service manual Service manual Uniq 150
2.22.1. VGA cable to interconnection of Uniq 150 with TDC-5000
1. Insulate cable on both ends and put tubing on particular wires.
2. Solder connectors on the cable.
3. Cover soldered places with tubing and shrink them with hot air.
4. Put covers on the connectors.
Figure 2.22.1. – VGA cable to interconnection of Uniq 150 with TDC-5000
D-SUB HD 15M D-SUB HD 15M
1
2
3
5, 7, 8, 10
6
9
12
13
14
15
1
2
3
5, 7, 8, 10
6
9
12
13
14
15
—
—
—
—
—
—
—
—
—
—
Pin number 5, 7, 8 and 10 solder together on both
connectors and lead them through one wire.
Pin number 4 and 11 do not connect.
to VGA conn. of Uniq 150 (15M)
to VGA conn. of TDC-5000 (15M)
Front view
1
6
11
5
10
15
Front view
1
6
11
5
10
15
Needed to order Quantity Ord. code
Tubing 1,6 × 10 mm 20 M010003
Cable CAB8 9 × 0,22 mm shielded 250 mm M200009
VGA connector D-SUB 15M 3-row on cable 2 M190119
Cover for Canon 9 2 M190006
2.23. Installation of ED-5000 to Uniq 150
Installation means conjunction Uniq 150 and ED-5000 to a one device.
ED-5000 and Uniq 150 as one
device loose its IP protection class!
2.23.1. Adjustment of ED-5000 leg
1. Adjust display leg according to figure. Leg should just sat on rear Uniq 150 cover.
2. Spread Loctite 403 power glue arround the perimeter of insert and put the insert into the display leg.
3. Put display leg in rear display cover according to figure.
4. Put arresting part in rear display cover. First put the lockers of arresting part (marked with arrows) into the locker
holes (also marked with arrows).
5. Then fix arresting part to the rear display cover with screws.
Note: It must be possible to turn display leg aside the display cover. Leg must carry the display weight but also
inclination must be adjustable.
Needed to order Quantity Ord. code
Insert of UniqPC/ED5000 leg 20 × 7,3 × 11 mm 1 M040571
Figure 2.23.1. – Adjustment of ED-5000 leg
Finish cutting/grinding
Insert of UniqPC/ED5000 leg 20 × 7,3 × 11 mm
Screw 2,9 × 9,5 mm
Leg of ED-5000
Arresting part of display
Rear ED-5000 cover
2.23.2. Cable to interconnection of PC 150 with ED-5000
1. Shorten cable with 5-pin connetor to 50 mm and remove yellow wire from the connector.
2. Cut 200 mm of cable DB 9F from the end without connector. *(It is possible to use any 200 long wires.)
3. Solder flat cable and also half of cable with 2-pin connector on the end of cable DB 9F. Soldered places cover with
tubing.
4. Solder 2-pin connector on the remains of 2-wire cable from previous step and oposit end of the cable solder to PCB
Pico Power on XC1.It is necessary to observe polarity! Soldered places cover with tubing.
Next steps execute after placing the cable to the display leg through rear cover of Uniq PC 150.
Needed to order Quantity Ord. code
Cable with 5-pin connector 100 mm 1 M200030
Cable DB 9F + DC JACK for ED-2500R 1 /
7
M200060 *
Tubing 1,6 × 10 mm 8 M010003
Tubing 2,4 × 10 mm 3 M010004
Cable with 2-pin connector 140 mm 1 M200029
Self tapping connector 40 pin RM = 2 mm 1 M190218
Flat cable RM 1 mm 40 mm M200155
Connector 2-pin M24112 1 M190080