elco AEROTOP G, Инструкция по установке, эксплуатации и обслуживанию, Страница: 6 / 58

General information
Legal guidelines, warranty conditions,
checks on delivery
General indications
The sizing, installation, com-
missioning and maintenance of
the products described in this
document can only be carried
out by qualified specialists.
Please comply with local legal
instructions, which may differ
from the directions given in this
document.
These instructions are necessary to
correctly install, adjust and maintain
the appliance. It is therefore essential
to read the following instructions care-
fully and to have the heat pump in-
stalled, tested and maintained by
qualified technicians with specific
training.
At the end of the period of warranty,
the manufacturer declines all respon-
sibility for mechanical, hydraulic or
electrical modifications. In the event
of explicitly unauthorised interven-
tions, carried out in breach of these
instructions, the warranty shall be
forfeit with immediate effect.
During installation, the specific operat-
ing safety regulations must be com-
plied with. Please check that the prop-
erties of the power supply match the
heat pump details (identification tag).
These instructions and the heat
pump's electrical system must be
stored with due care and attention
and, if necessary, made available to
the relevant personnel.
The manufacturer declines all
responsibility for damages to
individuals and property
caused, directly or indirectly, by
failure to comply with these
instructions.
The appliance body can only be
opened by a qualified techni-
cian.
Binding indications and directives
The construction and manufacture of
the heat pump complies with all Euro-
pean regulation directives (see EC
declaration of conformity).
The power connection of the
heat pump must be carried out
in compliance with national
appliance regulations. In addi-
tion, it is necessary to comply
with the connection conditions
of the local energy provider.
Additional indications and instruc-
tions.
Functional or surface-ready heating
with the heat pump according to DIN
EN 1264 is only possible if taking into
account the aforementioned condi-
tions.
After sizing the heat pump for nor-
mal operations, it may not be possi-
ble to generate all heating neces-
sary.
Please comply also with the following
instructions:
•
Comply with regulations and in-
structions issued by the screed
manufacturer of the screed mortar!
•
Correct operations are possible
only with a system that has been
installed up to standards
(hydraulics, electrical components,
settings)!
Otherwise the screed
could be damaged!
Because overloading could
cause serious damages, it is
forbidden to activate the heat
pump if the following conditions
apply:
•
construction drying out;
•
System temperature < 25 °
C . It is recommended to
heat with the use of electrical
resistance installed
•
unfinished system
(raw construction);
•
external doors and windows
not completed and closed.
In these cases, it is necessary
to make provisions for site
heating.
Warranty terms
The warranty for heat pumps is valid
for 24 months from the day of deliv-
ery. For everything else, the sale,
provision and warranty conditions
apply on the basis of the order con-
firmation.
Our warranty provisions shall be for-
feit for damages as a result of:
•
improper use, misuse or non-
compliant use
•
incorrect installation or commis-
sioning by the purchaser or
third
parties
•
addition of parts from other manu-
facturers
•
usage of the system with exces-
sive pressure or pressure outside
the indicated factory levels
•
failure to comply with the instruc-
tions contained in the manual
Checks on delivery
The appliances are delivered on a
wooden pallet, packed in cardboard.
At the time of delivery, please check
that the appliance wasn't damaged in
transport and that the equipment is
complete.
If you do find any damage, this
must be reported immediately on
the transport document with the
following wording: «Delivery ac-
cepted with reserved due to obvi-
ous damages».
The utmost care has been used in
manufacturing the heat pump.
However, during the manipulation of
the evaporator, it isn't possible to ex-
clude a slight bending of the single
blades during production. This does
not constitute a defect in the product.
For more information, please see
product description: high-efficiency
visible evaporator.
6