Edwards nEXT 55 Скачать руководство пользователя страница 25

Страница: 25 / 116

WARNING: DANGEROUS GASES

Risk of damage to equipment. In the interstage and booster versions of the

nEXT pumps, gas pumped through the interstage port will mix with gas pumped

through the pump inlet. Make sure that the gases do not react or combine to form

dangerous gases and substances.

WARNING: VACUUM EXPOSURE

Risk of injury. Do not expose the part of the human body to the vacuum.

WARNING: MERCURY VAPOUR

Risk of damage to equipment. Do not use a nEXT pump to pump mercury vapour. Do

not allow mercury (for example, from a McLeod gauge) to come into contact with the

pump. If mercury vapour is pumped, the pump rotor can corrode and fail.

CAUTION: CONDENSABLE GASES

Risk of damage to equipment. Do not use the pump to pump particulates or

condensable media. Deposition can occur in the pump which will degrade the pump

performance and decrease the pump life.

CAUTION: OXYGEN CONTENT IN GASES

Risk of damage to equipment. Do not use the pump to pump gases that contains

more than 20% oxygen. This can cause the lubricant to polymerise and the pump can

fail.

Note:

Concentrations of gases can be changed by the compression of the pump.

The pump is designed to pump the gases that follow:

▪

Air

▪

Carbon monoxide

▪

Neon

▪

Nitrogen

▪

Krypton

▪

Argon

▪

Carbon dioxide

▪

Helium

▪

Hydrogen

To pump a gas that is not listed, contact the supplier for advice. Failure to contact the

supplier can invalidate the warranty of the pump. The pump is not applicable for

pumping aggressive or corrosive gases.

07/2021 - ©Edwards Limited

Page 25

B8G000880_E

B8G000880_E - Technical data

Содержание nEXT 55





















































































































Результаты поиска

Содержание nEXT 55

Отзывы:

Бренды по названию

Популярные бренды

Edwards nEXT 55, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT 55

Отзывы:

Бренды по названию

Популярные бренды