Edwards nEXT 55 Скачать руководство пользователя страница 103

Страница: 103 / 116

12. Spares

CAUTION: SUPPLIED SPARES

Risk of damage to equipment. If you use spares that are not supplied by us, it will

decrease the reliability and performance of the pump. This will also invalidate the

product warranty.

12.1 Inlet screen

Inlet screens are installed to the pumps as supplied to prevent damage from the entry of

debris into the pump.

Table 42

Inlet screens

Flange Size

Item Number

DN63CF (10 off kit)

B72240807

DN63CF (1 off kit)

B72240860

12.2 Inlet strainer

The interstage pumps are supplied with an inlet strainer for the interstage port.

Table 43

Inlet strainers

Flange Size

Inlet Screen

DN25ISO

‑

A22305067

12.3 Inlet flange seals and integrated inlet screens

The pumps are supplied with an inlet seal.

Table 44

Inlet flange seals and integrated inlet screens

Flange size

Inlet flange seal

Item number

DN100ISO-K

ISO100 trapped O-ring with integrated coarse inlet

screen

B81000808

DN100ISO-K

ISO100 trapped O-ring with integrated fine inlet

screen

B81000809

DN63ISO-K

ISO63 trapped O-ring with integrated coarse inlet

screen

B8G200808

DN63ISO-K

ISO63 trapped O-ring with integrated fine inlet screen

B8G200809

NW40

NW40 centring o-ring with integrated coarse inlet

screen

C10516085

07/2021 - ©Edwards Limited

Page 103

B8G000880_E

B8G000880_E - Spares

Содержание nEXT 55





















































































































Результаты поиска

Содержание nEXT 55

Отзывы:

Похожие инструкции для nEXT 55

Бренды по названию

Популярные бренды

Edwards nEXT 55, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT 55

Отзывы:

Похожие инструкции для nEXT 55

Бренды по названию

Популярные бренды